Sierra Wireless DART 200 Скачать руководство пользователя страница 149

Страница: 149 / 206

DART 200 CDPD Modem User’s Guide

F DART AT Command Set

PN1197-00 Revision 1.0

F-5

Table F-1. Commands beginning with letters (cont.)

Command Mode Echo

Controls the echoing of characters when the modem is in command mode.

Format:

ATE0

Disable command mode character echo

ATE1

Enable command mode character echo (default)

Result codes:

Valid argument

ERROR

Invalid argument

Online Mode Echo

Controls the echoing of characters when the modem is in online mode.

Format:

ATF0

Enable online mode character echo

ATF1

Disable online mode character echo; permit remote echo if provided (default)

Result codes:

Valid argument

ERROR

Invalid argument

Hang-up (close connection)

Terminates the current connection. The command can be interrupted by input from the Mobile
Application Subsystem (MAS). This allows the terminate connection process to be upgraded from

if required.

Format:

ATH0

Transmit pending information, then terminate connection

ATH1

No action taken; return result code OK

ATH2

Discard pending data, and terminate connection immediately

ATH3

Discard pending data, terminate connection immediately, and deregister from
the network

Result codes:

Valid argument

ERROR

Invalid argument

Identify

Returns information about the DART.

Format:

ATI0

Show modem equipment ID

ATI1

Show modem software version number

ATI2

Identify manufacturer

ATI3

Identify equipment model number

Содержание DART 200















































































































































































































Результаты поиска

Содержание DART 200

Отзывы:

Sierra Wireless DART 200, Руководство пользователя, Страница: 149 / 206

Результаты поиска

Содержание DART 200

Отзывы: