Sierra Wireless DART 200 Скачать руководство пользователя страница 152 | Manualshive

Страница: 152 / 206

background image

DART 200 CDPD Modem User’s Guide

F DART AT Command Set

Sierra Wireless, Inc.

F-8

Table F-1. Commands beginning with letters (cont.)

X

Extended Result Codes

Selects whether the DART enables extended result codes. By default all result codes are enabled.

Format:

ATX0

Enable only codes 0...4 Extended results are mapped as appropriate to code 0...4

ATX1

Enable all extended result codes (default)

Result codes:

OK

Valid argument

ERROR

Invalid argument

Z

Soft Reset

Performs a soft reset on the DART, aborting any active connection, and resets all modem profile
parameters to their saved values. The network registration status is not affected.

Format:

ATZ

Perform soft reset

Result code:

OK

Command complete

?

Read Selected Register

Returns the value of the register selected by the

S

command.

Format:

AT?

Read value of most recently selected register

ATSn?

Read value of register

<n>

ATS?

Read value of register 0

Result codes:

A numerical value, decimal or hexadecimal (denoted by a leading 0x), representing the contents of
the specified S-Register.

ERROR

Invalid register number

=

Write Selected Register

Alters the value in the currently selected S-Register. The format of the parameter is numeric or text,
depending on the particular register being modified. Numeric values are specified in decimal. If the
S register contains text then this command must be last on the command line.

Format:

ATSn=x

Set register

<n>

to

<x>

AT=x

Sets selected register (last one referenced explicitly) to

<x>

Result codes:

OK

Valid parameter value

ERROR

Invalid value for selected register, or register is read only (RO)

NOT ENABLED

Must be in Service Provider mode to alter this register

«
...
150
151
152
153
154
...
»

Содержание DART 200















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DART 200

Бренд: TP-Link Страницы: 98

FSMODEM-CELLBASE

Бренд: Federal Signal Corporation Страницы: 16

MA02-AAC 2220 Series

Бренд: Ebyte Страницы: 41

PlantLinc PLR5000

Бренд: Data-Linc Group Страницы: 31

Бренд: Zte Страницы: 16

Бренд: Teledyne Страницы: 3

Бренд: Tait Страницы: 30

HomeConnect 3CR29220

Бренд: 3Com Страницы: 38

Бренд: Aritech Страницы: 10

Бренд: SMC Networks Страницы: 109

Бренд: Radio Shack Страницы: 8

Бренд: PairGain Страницы: 86

Бренд: Tainet Страницы: 131

Бренд: Data Connect Страницы: 23

Бренд: XtendLan Страницы: 105

Бренд: AARCOMM Страницы: 12

Бренд: Paradyne Страницы: 2

Бренд: Cradlepoint Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды