Sierra Wireless DART 200 Скачать руководство пользователя страница 106 | Manualshive

Страница: 106 / 206

background image

DART 200 CDPD Modem User’s Guide

8 Application Programming

Sierra Wireless, Inc.

8-12

2.

To use the ATA method, the MAS must have a device. Read
command is pending on the COM port and issues an

ATA

command

in response to the incoming Ring.
OR
S-Register 0 = 1 enables the DART 200 to remain permanently in
auto answer mode; making call answering fully automatic
(recommended, especially) when dealing with low intelligence
terminals not capable of issuing an

ATA

command.

3.

To answer automatically set S-Register 0=1 enabling the DART to
remain permanently in auto answer mode; making call answering
fully automatic. This is the recommended method, especially when
dealing with low intelligence terminals not capable of issuing an

ATA

command.

4.

Completion of call establishment at the server in both TCP and UDP
modes of operation is indicated by a CONNECT message (verbose
mode) or 1 response (terse mode). This response can be suppressed,
if necessary, by putting the modem in Quiet Mode (

ATQ1

).

To set up the DART 200 server for auto answer, use the following
commands:

1.

AT*An

to activate the appropriate server (1 for TCP, 2 for UDP).

2.

ATS0=1

to enable auto answer.

3.

AT*Ln

to set the listening port. Set the port number in the range

1025 to 4999 (default listening port is 2100 for backward
compatibility and can be left unchanged).

4.

AT&W

to save settings.

5.

Incoming connection requests must reference the listening port. For
example, a TCP establishment request from another DART would be

ATDTn.n.n.n/2100.

This information applies for calls between DARTs, or for calls to a
DART when operating in TCP, UDP, or telnet modes of operation.

Flow control considerations

Flow control is used by a device receiving data over the RS-232 interface
to prevent the transmitting device from sending data faster than the
receiver can process it. The DART 200 supports hardware flow control,
Request to Send (RTS)/Clear to Send (CTS), and Software flow control,
XON/XOFF.

The DART 200 also operates without flow control, leaving you to ensure
that data overruns do not occur. This feature is specified by the

\Qn

option; the default is

\Q2

Hardware Flow Control.

?

?

NOTE:
Flow control is only
active when in online
mode.

«
...
104
105
106
107
108
...
»

Содержание DART 200















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DART 200

DCM202 - Express Ethernetwork DOCSIS 2.0 Cable...

Бренд: D-Link Страницы: 33

Бренд: U.S. Converters Страницы: 33

MOONLANDER 2 SCRYPT

Бренд: Futurebit Страницы: 12

NETRONIX THIAMIS 8535

Бренд: TSI Instruments Страницы: 4

Бренд: Aztech Страницы: 32

Prestige 650M-17

Бренд: ZyXEL Communications Страницы: 89

Бренд: NetComm Страницы: 139

Бренд: Orion Telecom Networks Страницы: 16

Бренд: Moultrie Mobile Страницы: 7

Бренд: Vega Absolute Страницы: 23

Бренд: Zte Страницы: 2

Бренд: Zte Страницы: 12

Бренд: Zte Страницы: 25

Бренд: Realme Страницы: 24

Бренд: PROLiNK Страницы: 12

Hurricane 9000S

Бренд: PROLiNK Страницы: 36

Бренд: Zoom Страницы: 2

Бренд: Zoom Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды