manualshive.com logo in svg

Sierra Wireless DART 200, Руководство пользователя, Страница: 173 / 206

Поделиться
Скачать
Sierra Wireless DART 200 Скачать руководство пользователя страница 173

DART 200 CDPD Modem User’s Guide

F DART AT Command Set

PN1197-00 Revision 1.0

F-29

Table F-6. Service Provider commands beginning with caret (^) (cont.)

^S

Set DART SLIP Address

Sets the SLIP IP Address of the Modem. This internal address is a private address between the modem
and the terminal connected to the serial port and is unknown to the network. This address is often
referred to as being the gateway, router or server address by the TCP/IP stacks that support SLIP
operation.

Since the SLIP address is known only to the terminal and the modem, the convention is to use 1.1.1.2
for this address.

NOTE:
A SLIP address is required to permit the DART to operate in SLIP mode.

Format:

AT^Sn

Where 

n

 = the IP address of the modem SLIP port. The format is

nnn.nnn.nnn.nnn.

Result codes:

OK

Valid argument

ERROR

Invalid argument

NOT ENABLED

Modem is not in service provider mode

Содержание DART 200















































































































































































































Отзывы:

Нет отзывов