Sierra Wireless DART 200 Скачать руководство пользователя страница 177 | Manualshive

Страница: 177 / 206

background image

PN1197-00 Revision 1.0

G

Loading DART 200
Firmware

Periodically, the DART 200 firmware needs to be updated, because of
improvements to the DART’s capabilities, corrections for problems, or to
keep pace with the evolving CDPD standard.

When this need occurs, a

ZIP file containing the upgrade materials will be available on the Sierra
Wireless Web site. If you do not have Internet access this file will also be
available on diskette. The ZIP file will contain the new firmware, a
download program, and a README file with instructions for loading the
firmware onto your DART 200 modem.

The download program runs under DOS, and can run as standalone or in
a DOS window under Windows. To reduce the possibility of time-outs it
is recommended that the files and program be copied to a hardfile before
starting execution. Time-outs can still occur if running under Windows.
If a retry or two does not eliminate the timeout problem, try to download
at a lower speed. If that also times out then run the download function as
a standalone program outside of Windows.

When the download is complete the last step in the process is for the
loader to issue an

AT&F&W

to restore and save the DART’s factory

defaults.

If the modem is personalized for application use, reprogram the

modem with its application specific profile and S-Register settings.
However, loading the new firmware does not disturb the modem’s IP
address(s) and associated credentials. When the download is complete,
the modem registers on the CDPD network with no problems.

Firmware download procedure

Perform the following steps to download the new software to the DART
200.

1.

Make the appropriate connections by:

•

Connecting the modem to a 12 VDC power supply

•

Connecting the modem’s RS-232 interface to a serial port on
your PC

2.

Power on the modem.

3.

Check that the modem’s server functions are inactive before starting
the download process. Start your ASCII terminal emulator and enter
an

AT&V

command.

Appendix

?

?

NOTE:
The download function
will reset the modem
profile but not the IP
Address or credentials.

«
...
175
176
177
178
179
...
»

Содержание DART 200















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DART 200

Бренд: AT&T Страницы: 8

Бренд: NAL Страницы: 101

NetLink 1082/144

Бренд: Patton electronics Страницы: 32

Бренд: Satel Страницы: 30

Бренд: Aztech Страницы: 32

Бренд: NetComm Страницы: 28

Spartan 57076-1

Бренд: Traxxas Страницы: 30

Бренд: Huawei Страницы: 8

Бренд: Huawei Страницы: 22

Бренд: Huawei Страницы: 9

Бренд: Huawei Страницы: 2

Бренд: Huawei Страницы: 15

Бренд: Huawei Страницы: 4

Бренд: Huawei Страницы: 36

Бренд: Huawei Страницы: 9

Бренд: Huawei Страницы: 15

Бренд: Huawei Страницы: 2

Бренд: Huawei Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды