Sierra Wireless DART 200 Скачать руководство пользователя страница 185

Страница: 185 / 206

DART 200 CDPD Modem User’s Guide

Glossary

PN1197-00 Revision 1.0

Glossary-5

M-ES

Mobile End System

Refers to the DART as a component in the CDPD
network

MDBS

Mobile Data Base Station

Cellular tower serving a specific geographical area.
Communicates by radio with the DART and by landline,
microwave, etc. with the MDIS.

See also,

cell.

MDIS

Mobile Data Intermediate Station

Computer device that serves as the control point for
CDPD in a specific area. Accepts information from
MDBS and processes and sends the information by
routers to the appropriate F-ES.

MDLP

Mobile Data Link Protocol

The link layer protocol used in CDPD.

Operates between

the SNDCP and MAC layers. Provides framing, data link
connection, sequence control, and flow control functions.

MDT

Mobile Data Terminal

An alternate name for a mobile MAS.

MNRP

Mobile Network Registration Protocol

MTSO

Mobile Telephone Switching Office

Some carriers locate their MDIS at the MTSO
(pronounced

mitso

)

NEI

Network Entity Identifier

The official name for the IP Address. A 32-bit identifier
normally expressed in dotted decimal (162.147.11.49).
The NEI is a component of the NSAP.

NEMA

National Electrical Manufacturer’s Association

A standards setting body.

NSAP

Network Service Access Point

The definition of the point where the service user and
service provider systems meet. The NEI is accessed
through the NSAP by end-users.

OPR

Abbreviation for the Operate light on the DART

Indicates power on status (slow blink), and relative signal
strength (faster blink to solid on).

PAD

Packet Assembler - Disassembler

PIN

Personal Identification Number

Part of the optional CDPD security system.

Содержание DART 200















































































































































































































Результаты поиска

Содержание DART 200

Отзывы:

Похожие инструкции для DART 200

Бренды по названию

Популярные бренды

Sierra Wireless DART 200, Руководство пользователя

Результаты поиска

Содержание DART 200

Отзывы:

Похожие инструкции для DART 200

Бренды по названию

Популярные бренды