Sierra Wireless DART 200 Скачать руководство пользователя страница 187

Страница: 187 / 206

DART 200 CDPD Modem User’s Guide

Glossary

PN1197-00 Revision 1.0

Glossary-7

SIE

Symbols In Error

Count of how many 6-bit symbols (used by the FEC to
organize the data stream) were in error in the last data
block.

See also,

FEC.

SIM

Subscriber Identity Module.

The part of the modem containing the IP Address and
authentication credentials

SLIP

Serial Line Internet Protocol

The original alternative communications protocol used
between computers, or between computers and routers on
the Internet.

See also,

PPP.

In CDPD the modem will operate in SLIP mode when the
TCP stack function is provided by software rather than
the modem.

SPI

Service Provider Identifier

An alternate identifier for a CDPD service provider. Can
be used for special services or billing purposes (CDPD
1.1 only).

SPNI

Service Provider Network Identifier

A unique numeric code used to identify the CDPD service
provider.

SNDCP

Subnetwork Dependent Convergence Protocol

Operates between the MDLP and IP layers. Provides
compression, encryption, and segmenting functions.

SNMP

Simplified Network Management Protocol

Permits remote monitoring and control of communication
devices.

Subscriber Unit

This refers to the DART as a component in the CDPD
network

TCP

Transmission Control Protocol.

A guaranteed packet delivery Internet protocol that is
built on (uses) Internet Protocol (IP) as a base. Often
referred to as TCP/IP

TEI

Temporary Equipment Identifier

A data link layer frame address that identifies a specific
M-ES as the source or destination.

TNC

An RF connector type commonly used with the coaxial
cables on cellular antennas

TXD

Transmitted Data. One of the RS-232 data lines

Содержание DART 200















































































































































































































Результаты поиска

Содержание DART 200

Отзывы:

Похожие инструкции для DART 200

Бренды по названию

Популярные бренды

Sierra Wireless DART 200, Руководство пользователя

Результаты поиска

Содержание DART 200

Отзывы:

Похожие инструкции для DART 200

Бренды по названию

Популярные бренды