manualshive.com logo in svg

Sierra Wireless DART 200, Руководство пользователя


Поделиться
Скачать
background image

DART 200 CDPD Modem User’s Guide

5 DART Supported Protocols

PN1197-00 Revision 1.0

5-21

Host TCP setup

The host (client) modem is set up to support polling of remote devices by
the host computer. The host uses flow control and the data being sent is
binary, not character data. The polling function does not require the TCP
server, but requires flow control, and timed data forwarding because of
the binary data.

Use this setup only for bench testing or a limited use trial. A production
application uses a leased line, frame relay, or Internet connection
between the host and the MDIS instead of a modem. In the latter
scenario, the production host application needs to include a software
stack (replacing the modem stack) to operate with the CDPD network.

In Table 5-4, only the line items marked with an

 R 

(required) or an 

O

(optional) are changed from the default (D).

Table 5-4. Host TCP setup

AT Command

Req Opt Def Description

AT^Annn.nnn.nnn.
nnn

R

Input IP Address (if not already done)

AT\N[1,2]

R

Side Preference (get from carrier)

AT\J0

D

Use default - No channel access
restrictions

AT\R4

R

Auto Registration at Power On

ATS13=0

R

With AT\R4 sets Continuous Automatic
Registration

AT\O0

R

PAD mode is required for TCP.

AT*A0

D

Use default - No server required

AT*L2100

D

Use default - Listen on port 2100

ATE0

O

No command mode character echo

ATV0

O

Use terse result codes

ATQ0

D

Use default - Result codes are sent to the
host

ATF1

D

Use default - Do not echo transmitted
data to the host

ATX1

D

Use default - Extended result codes

AT&C1

D

Use default - DCD follows state of the
connection

AT&D0

D

Use default - You may want to consider
using DTR to escape

AT&E2

O

Filter escape sequence from output

AT&S0

D

Use default - DSR is always active

AT\F3

D

Use default - Applies only if \M1
specified

AT\M0

D

Use default - Do not recognize data
forwarding characters

AT\Q2

D

Use default - Most PC’s use flow
control

AT\T1

D

Timed data forwarding - Always use
with binary data

AT*B0

D

Use default - Does not apply to TCP

AT*C1

D

Use default - Does not apply to TCP

AT*G1

D

Use default - Does not apply to TCP

Содержание DART 200















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DART 200

OUMAN GSMMOD4 Manual preview
GSMMOD4
Бренд: OUMAN Страницы: 4
Raveon RV-M3-M Manual preview
RV-M3-M
Бренд: Raveon Страницы: 32
TURBOCOMM EC420 User Manual preview
EC420
Бренд: TURBOCOMM Страницы: 6
Alcatel AlcatelPCNT02A Installation Manual preview
AlcatelPCNT02A
Бренд: Alcatel Страницы: 33
Digi E230 User Manual preview
E230
Бренд: Digi Страницы: 19
KWorld PlusTV Hybrid Stick Hardware Installation preview
PlusTV Hybrid Stick
Бренд: KWorld Страницы: 10
Billion BIPAC-5100S User Manual preview
BIPAC-5100S
Бренд: Billion Страницы: 72
Kasda KW 58283 User Manual preview
KW 58283
Бренд: Kasda Страницы: 40
Kasda KW5863 User Manual preview
KW5863
Бренд: Kasda Страницы: 41
Ebyte E34-DTU User Manual preview
E34-DTU
Бренд: Ebyte Страницы: 17
Ebyte 2G4HD12 User Manual preview
2G4HD12
Бренд: Ebyte Страницы: 24
Ebyte E180-DTU User Manual preview
E180-DTU
Бренд: Ebyte Страницы: 35
Ebyte 400SL22P User Manual preview
400SL22P
Бренд: Ebyte Страницы: 35
2Wire i38HG User Manual preview
i38HG
Бренд: 2Wire Страницы: 108
GDI COMMUNICATIONS SM336 Manual preview
SM336
Бренд: GDI COMMUNICATIONS Страницы: 31
GDI COMMUNICATIONS FLD2SA Series Manual preview
FLD2SA Series
Бренд: GDI COMMUNICATIONS Страницы: 21
GDI NT 200R-Plus User Manual preview
NT 200R-Plus
Бренд: GDI Страницы: 21
3Com 3CP5610A - U.S. Robotics 56K V90 PCI Performance Pro Faxmodem Dos/NT/Linux User Manual preview
3CP5610A - U.S. Robotics 56K V90 PCI Performance Pro Faxmodem Dos/NT/Linux
Бренд: 3Com Страницы: 100

Бренды по названию

Популярные бренды

Загрузить еще бренды