Sierra Wireless DART 200 Скачать руководство пользователя страница 155 | Manualshive

Страница: 155 / 206

background image

DART 200 CDPD Modem User’s Guide

F DART AT Command Set

PN1197-00 Revision 1.0

F-11

Table F-2. Commands beginning with ampersand (&) (cont.)

&L

Set DART Line Speed and Format

For serial ports, this command allows the Mobile Application Subsystem (MAS) to set the line speed
and format. All subsequent communications between the MAS and the DART is at the new speed and
format if the command completes successfully. These settings do not survive a modem power cycle
unless saved with an

&W

.

The serial port interface to the MAS is configured to the line speed (300, 1200, 2400, 4800, 9600, or
19200), data bits per character (7 or 8), parity (O, E, N) and number of stop bits (1 or 2) specified. If
any of these are invalid none of the settings are changed.

Regardless of the interface speed selected, the airlink speed is still 19200.

The modems default is 9600, 8N1

with

autobaud active.

NOTE:
Executing this command disables the modem’s autobaud feature. This is desirable for most
applications. However, autobaud can be reactivated if desired with the AT&L1 command.

Format:

AT&L<s>,<bps>

Deactivate autobaud feature and set the modem as specified

•

s

= desired line speed

•

b

= number of data bits (7 or 8)

•

p

= parity (O for odd, E for even, N for none)

•

s

= number of stop bits (1 or 2)

Examples:

AT&L9600,8N1

AT&L19200,7E1

AT&L1

Reactivate autobaud feature

Result codes:

OK

Valid argument

ERROR

Invalid argument

&S

Set DSR Operation

For serial ports, this command defines the operation of the data set ready signal (DSR) at the DART’s
RS-232 interface. This signal can then be tested by the MAS application to determine if the specified
condition is true. Refer to Chapter 8, Application Programming

, Data and control interface,

for more

information.

Format:

AT&S0

DSR is always active (default)

AT&S1

DSR follows the state of the Connection

AT&S2

DSR follows the state of RF in Range

AT&S3

DSR follows the state of Registration

Result codes:

OK

Valid argument

ERROR

Invalid argument

«
...
153
154
155
156
157
...
»

Содержание DART 200















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DART 200

Бренд: Dantel Страницы: 14

MA02-AAC 2220 Series

Бренд: Ebyte Страницы: 41

Бренд: Ebyte Страницы: 11

Бренд: LG Страницы: 17

Бренд: ComBlock Страницы: 22

Бренд: CSI Страницы: 8

xComfort CKOZ-00/14

Бренд: Eaton Страницы: 2

Бренд: Tut Systems Страницы: 20

Бренд: 3 Com U.S. Robotics Страницы: 1

Skywire NL-LTE-TNAG

Бренд: NimbeLink Страницы: 8

OnSite 1052 Series

Бренд: Patton electronics Страницы: 4

Бренд: Embedded Planet Страницы: 48

NoWire CellConnect

Бренд: Submeter Solutions Страницы: 4

Бренд: XtendLan Страницы: 105

Бренд: Comet Страницы: 39

Бренд: Patton electronics Страницы: 12

Бренд: Draytek Страницы: 8

V.92 PCI Pro Modem 0530-0276-000

Бренд: ActionTec Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды