manualshive.com logo in svg

Sierra Wireless DART 200, Руководство пользователя, Страница: 88 / 206

Поделиться
Скачать
Sierra Wireless DART 200 Скачать руководство пользователя страница 88

DART 200 CDPD Modem User’s Guide 

6 Device Attachment

Sierra Wireless, Inc.

 

6-2

Figure 6-2. Stand-alone RS-232

The problem with this occurs when modems are inserted between the
DTE and a remote device with a DCE interface. The modem expects to
communicate with a DTE interface. Since this is not the case at the
remote end, where the DCE modem is trying to talk to a DCE device, a
communications failure results. The solution for this situation is a null
modem connector. A typical null modem pin out is shown in Table 6-1.

Table 6-1. Typical null modem pinout

Female
 DB9

Male
 DB9

1 DCD

4

2 RXD

3

3 TXD

2

4 DTR

6 and 1

5 SGD

5

6 DSR

4

7 RTS

8

8 CTS

7

9  ---

Open

The null modem adapter corrects the mismatch between the modem and
a terminating device having a DCE interface. The proper location for the
null modem is shown in Figure 6-3.

Figure 6-3. Null modem location

Computer

DTE

Terminal

RS-232

DCE

Computer

DTE

Terminal

RS-232

Modem

Modem

RS-232

DCE

Phone

Line

DCE

DCE

Null modem
needed here

Содержание DART 200















































































































































































































Отзывы:

Нет отзывов