Sierra Wireless DART 200 Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 206

background image

DART 200 CDPD Modem User’s Guide

2 Installation and Setup

PN1197-00 Revision 1.0

2-13

•

By viewing the Network Status Register (S-Register 57) with the

AT&V

command or the

ATS57?

command. This is the

recommended method, because viewing S-Register 57 shows other
useful information, as shown in Figure 2-3

Figure 2-3. Viewing the network S-Register (S57)

ATS57?

160

OK

A value of 128 (bit 7 on) or higher indicates that the modem acquired
a channel. If auto-registration at power on (

AT\R4

) is specified, then

the value is 160 (bits 5 and 7 on) or 161 (bit 0 also on) indicating that
it completed registration.

If the DART cannot acquire a channel, move the antenna to a better
location. To determine the best location for the antenna you need some
indication of received signal strength. This is given by the RSSI; one of
the radio resource values. View RSSI with the

ATS102?

or the

AT&V+

command.

Figure 2-4 is a snapshot of the CDPD channel at a specific point in time.
View this data several times to see if the modem is staying on a single
channel (S-Register 100) or continues to search. If the value in
S-Register 101 is a zero, then the search is continuing.

Figure 2-4. Monitoring the CDPD channel

at&v+

DART 200
S100:00799 S101:00001 S102:-0073 S103:00002 S104:00040 S105:00000
S106:00001 S107:00000 S108:00022 S109:00010 S110:00079 S111:00001
S112:00000 S113:00000 S114:00000 S115:00000 S116:00000 S117:00000
S118:00018 S119:0FFFF S120:00000 S121:00002 S122:00000 S123:00002
S124:00030 S125:14400 S126:00005

If the modem cannot acquire a usable channel (S-Register 101 = 1) after
a few minutes there are several possible causes:

•

The signal strength is too weak

•

The cell is not currently CDPD capable (check with your cellular
carrier)

•

The modem has an incorrect channel restriction configuration. Use
the

AT&V

command to check the

\Jn

setting

•

The side setting is wrong. Use the

AT&V

command to check the

\Nn

setting

•

There is an interference problem

•

The modem is faulty

«
...
35
36
37
38
39
...
»

Содержание DART 200















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DART 200

Бренд: Sel Страницы: 16

Бренд: XtendLan Страницы: 73

Бренд: Abocom Страницы: 19

Бренд: TP-Link Страницы: 4

FastLinc FLC820G

Бренд: Data-Linc Group Страницы: 24

Бренд: Data-Linc Group Страницы: 32

Бренд: GE Страницы: 5

HomeConnect 3CP4130

Бренд: 3Com Страницы: 74

Бренд: Teledyne Страницы: 3

Merlin for GPRS G201

Бренд: Novatel Страницы: 54

Бренд: MultiModem Страницы: 88

HomePortal 1500CW

Бренд: 2Wire Страницы: 78

Бренд: GDI COMMUNICATIONS Страницы: 31

Бренд: Spectrum Страницы: 12

SURFboard SB3100i

Бренд: General Instrument Страницы: 21

Бренд: Franklin Страницы: 22

Бренд: B&B Electronics Страницы: 2

ORBCOMM IDP-280

Бренд: SkyWave Страницы: 63

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды