Sierra Wireless DART 200 Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 206

background image

DART 200 CDPD Modem User’s Guide

5 DART Supported Protocols

Sierra Wireless, Inc.

5-12

Table 5-1. Remote UDP setup (cont.)

AT Command

Req Opt Def Description

ATE0

O

No command mode character echo

ATV0

O

Use terse result codes

ATQ0

D

Use default - Result codes are sent to
the RTU

ATF1

D

Use default - Do not echo transmitted
data to the RTU

ATX1

D

Use default - Extended result codes

AT&C1

D

Use default - DCD follows state of
the connection

AT&D0

D

Use default - You may want to
consider using DTR to escape if RTU
supports it

AT&E2

O

Filter escape sequence from output

AT&S0

D

Use default - DSR is always active

AT\F3

D

Use default - Applies only if \M1
specified

AT\M0

D

Use default - Do not recognize data
forwarding characters

AT\Q0

O

Most RTUs do not use flow control

AT\T1

D

Timed data forwarding - Always use
with binary data

AT*B0

D

Use default - Many CDPD Carriers
have not implemented Broadcast.

AT*C1

D

Use default - Does not apply to UDP

AT*G1

D

Use default - Does not apply to UDP

AT*K0

D

Use default - Does not apply to UDP

AT*R0

D

Use default - Does not apply to UDP

AT*T0

D

Use default - Does not apply to UDP

Host UDP setup

The host (client) modem is set up to support polling of remote devices by
the host computer. The specific host uses flow control and the data being
sent is binary, not character, data. The polling function does not require
the UDP server, but requires flow control, and timed data forwarding
because of the binary data.

Use this setup only for bench testing or a limited use trial. A production
application uses a leased line, frame relay, or Internet connection
between the host and the MDIS instead of a modem. In the latter
scenario, the production host application needs to interface with a
software stack (replacing the modem stack to operate with the CDPD
network).

In Table 5-2, only the line items marked with an

R

or an

O

are changed

from the default (D). After making changes, save them with an

AT&W.

«
...
64
65
66
67
68
...
»

Содержание DART 200















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DART 200

Бренд: ADTRAN Страницы: 57

Бренд: Patton electronics Страницы: 24

Бренд: Ubee Страницы: 2

Бренд: Arcadian Networks Страницы: 17

Бренд: Sony Ericsson Страницы: 264

Бренд: Telit Wireless Solutions Страницы: 74

Бренд: Erco & Gener Страницы: 4

Бренд: TeleWell Страницы: 131

Бренд: Vahle Страницы: 16

Бренд: NetComm Страницы: 2

Бренд: Zte Страницы: 9

Бренд: Datum Systems Страницы: 94

Бренд: Warwick Страницы: 17

Бренд: Zte Страницы: 2

Бренд: Zte Страницы: 12

Бренд: Ebyte Страницы: 11

Бренд: Ebyte Страницы: 20

Бренд: Ebyte Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды