Sierra Wireless DART 200 Скачать руководство пользователя страница 162 | Manualshive

Страница: 162 / 206

background image

DART 200 CDPD Modem User’s Guide

F DART AT Command Set

Sierra Wireless, Inc.

F-18

Table F-3. Commands beginning with backslash (\) (cont.)

\T

Automatic Transmit Control

Enables the inter-character time-out data forwarding operation of the packet assembler in online mode.
When the time between characters received from the MAS exceeds the time-out value specified in
S-Register 50, the data in the packet buffer is transmitted. The time-out value is specified in tenths of
seconds; the default is 20 (2 seconds). Refer to Chapter 4, Broadcast and Multicast Operations,

Data

forwarding,

for more information, and Chapter 8, Application Programming,

Binary data transfer,

for

more information.

Format:

AT\T0

Disable automatic timed transmission

AT\T1

Enable automatic timed transmission (default)

Result codes:

OK

Valid argument

ERROR

Invalid argument

Table F-4. Commands beginning with asterisk (*)

*A

Select Server Type

Specifies the type of server to be used and can be issued at any time, stopping the current server process
and starting the requested process. Only one server type can be active at a given time.

The current server option can be viewed by inspecting the

*An

option in the modem profile by use of the

AT&V

command.

Format:

AT*A0

No server process. This is the default setting and is appropriate if the attached
device always operates in client mode, for example, always originating connection
requests with an

ATDT

command.

NOTE:
This command must also be used as an intermediate step when switching server
types

.

AT*A1

Selects TCP server process. This allows the modem to accept incoming TCP
connection requests when in command mode and is consistent with earlier versions
of the modem software. Refer to Chapter 5, DART Supported Protocols,

Basic

UDP,

for more information.

AT*A2

Selects UDP server process. This allows the modem to accept incoming UDP data
packets when in command mode. Refer to Chapter 5, DART Supported Protocols,

UDP Server characteristics

for more information.

Result codes:

OK

Requested server mode is set.

ERROR

Invalid argument.

«
...
160
161
162
163
164
...
»

Содержание DART 200















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DART 200

Бренд: Patton electronics Страницы: 5

Бренд: Aztech Страницы: 2

Бренд: Abocom Страницы: 1

Бренд: Data-Linc Group Страницы: 27

Бренд: Motorola Страницы: 12

Бренд: ELTEX Страницы: 6

Бренд: TRENDnet Страницы: 2

Бренд: TRENDnet Страницы: 54

Бренд: Shuttle Страницы: 5

COMSPHERE 3821Plus

Бренд: Paradyne Страницы: 28

Бренд: Spectrum Страницы: 8

Бренд: NETGEAR Страницы: 106

Cerberus P 6311-072

Бренд: Pentagram Страницы: 54

Бренд: US Robotics Страницы: 2

Бренд: US Robotics Страницы: 16

Бренд: Zte Страницы: 15

U.S. Robotics 56K Winmodem

Бренд: 3Com Страницы: 58

Бренд: US Robotics Страницы: 152

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды