Sierra Wireless DART 200 Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 206

background image

PN1197-00 Revision 1.0

4

Broadcast and Multicast
Operation

Overview

Broadcast and multicast are Cellular Digital Packet Data (CDPD)
functions that support sending the same data to a large group of IP
Addresses with a single transmission to the CDPD network. This
capability is implemented through Mobile Data Intermediate System
(MDIS) software.

The facility was originally defined for Fixed End System (F-ES) (host) to
Mobile End System (M-ES) (terminal) transmissions. However, some
MDIS manufacturers have implemented multicast to also support M-ES
to M-ES transmissions. Protocol restrictions prevent broadcast or
multicast messages from being encrypted. Check with your carrier to
determine if these capabilities are offered before planning to use it as part
of your application.

Broadcast and multicast transmissions are point-to-multi-point and
provide a one-way connectionless service. The protocol used is User
Datagram Protocol (UDP) or another unacknowledged protocol that
operates over IP, for example, ICMP PING. The operational
considerations are:

1.

Broadcast or multicast data packets will not be received by a DART
200 with an active telnet or Transmission Control Protocol (TCP)
PAD session.

2.

If a User Datagram Protocol (UDP) PAD session is active the
broadcast and multicast messages will be interspersed with the
application data packets and must be separated by the application.

3.

In the case of Serial Line Internet Protocol (SLIP), the disposition of
the broadcast and multicast messages is a function of the support
provided by the software stack and end-user applications (one must
be UDP) operating on the Mobile Application Subsystem (MAS). If
a UDP session is not active, the messages will be lost.

«
...
49
50
51
52
53
...
»

Содержание DART 200















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DART 200

Бренд: Aztech Страницы: 32

Бренд: Intercel Страницы: 7

MA02-AAC 2220 Series

Бренд: Ebyte Страницы: 41

eSAM ITRON FC200

Бренд: Intercel Страницы: 12

Zlinx Xtreme ZXT24-RM

Бренд: B&B Electronics Страницы: 163

HomeConnect 3CP4130

Бренд: 3Com Страницы: 74

Бренд: ProSoft Technology Страницы: 136

Бренд: Proscend Страницы: 102

Бренд: ALZA Страницы: 32

Бренд: Broadxent Страницы: 60

Бренд: Four-Faith Страницы: 47

Бренд: Enfora Страницы: 41

Бренд: BroadMax Technology Страницы: 2

Бренд: Wellink Страницы: 32

Бренд: Zte Страницы: 24

Бренд: NAL RESEARCH CORPORATION Страницы: 114

Бренд: D-Link Страницы: 8

GTM-204M-4G Series

Бренд: ICP DAS USA Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды