Sierra Wireless DART 200 Скачать руководство пользователя страница 131 | Manualshive

Страница: 131 / 206

background image

PN1197-00 Revision 1.0

E

S-Registers

The configuration of the DART is accessible to the Mobile Application
Subsystem (MAS) as a set of parameters known as Status (S)-Registers.
Some registers can be updated directly with AT commands, others are
read-only. The set of registers and modem options (also set with AT
commands) is known as the configuration profile. At least three distinct
profiles are present in the DART, including:

•

Active Profile - Set of register values and options actually used as
the current operational parameters of the modem. Registers can be
queried individually with the

ATSn?

command, or modified using

the

ATSn=

command (where

n

= the S-Register number). The entire

profile, registers and options can be viewed with the

AT&V

command

•

Saved Profile - Used at power-up to establish the power-on
configuration state. It is created by the write profile (

AT&W

)

command, that copies the current active profile into the profile save
area. The saved profile is preserved across cold starts or
power-cycles. The saved profile can be recopied over the active
profile at any time with the soft reset (

ATZ

) command. Some CDPD

modems (but not the DART) can have more than one saved profile
available for use

•

Factory Profile - An embedded permanent profile that cannot be
modified from the factory default setting. The factory profile can be
copied into the active profile with the load defaults (

AT&F

)

command.

Register display formats

The S-Registers can be displayed in groupings by use of the

AT&V

commands:

AT&V

for S-Registers 0 through 99, and

AT&V+

for

S-Registers 100 through 126. The format of the data displayed by these
two

AT&V

commands is different. In addition, the format of the data

displayed by the

ATSn?

command is also different in many cases,

particularly for registers above 100. These variations are summarized
below.

Appendix

«
...
129
130
131
132
133
...
»

Содержание DART 200















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DART 200

Бренд: M/A-Com Страницы: 22

Бренд: P1 Страницы: 5

Бренд: P1 Страницы: 17

Бренд: P1 Страницы: 2

Бренд: Sagem Страницы: 4

Бренд: PROLiNK Страницы: 10

Бренд: CXR Страницы: 150

Zlinx Xtreme ZXT24-RM

Бренд: B&B Electronics Страницы: 163

Бренд: Elcon Страницы: 24

Бренд: Medion Страницы: 2

MicroLink-HM 101-0029

Бренд: Microflex Страницы: 17

oncell G2100 Series

Бренд: Moxa Technologies Страницы: 105

Cerberus P 6331-4A

Бренд: Pentagram Страницы: 62

Cerberus Wi-Fi Lite

Бренд: Pentagram Страницы: 64

Cerberus ADSL2+ Lite

Бренд: Pentagram Страницы: 75

Бренд: Hughes Страницы: 42

Бренд: Campbell Страницы: 22

Бренд: Zte Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды