Sierra Wireless DART 200 Скачать руководство пользователя страница 150 | Manualshive

Страница: 150 / 206

background image

DART 200 CDPD Modem User’s Guide

F DART AT Command Set

Sierra Wireless, Inc.

F-6

Table F-1. Commands beginning with letters (cont.)

I (cont.)

Result codes:

OK

Valid argument

ERROR

Invalid argument

NOT ENABLED

Must be in service provider mode

O

Enter Online Mode

Instructs the DART to return to the online state. Any following commands on the same command
line are ignored. This command is used to get to online mode following an

ATD

; command, or to

return to online mode following an escape.

NOTE:
To return to SLIP mode following an escape from SLIP use AT*S.

Format:

ATO

Go/return to online mode

Result codes:

ERROR

Connection does not exist

CONNECT

Successful return to online mode

Q

Quiet Mode

Controls whether result codes are sent to the Mobile Application Subsystem (MAS). If selected,
result codes can be further modified by the

V

and

X

commands.

Format:

ATQ0

Disable quiet mode (result codes are sent to the MAS) (default)

ATQ1

Enable quiet mode (result codes are not sent to the MAS)

NOTE:
There are some low intelligence devices (often found when retrofitting CDPD to a landline or
radio based system) that cannot accept any result codes.

Q1 is an appropriate setting for that class

of device.

Result codes:

<nothing>

If

ATQ1

selected; OK response is suppressed

OK

If

ATQ0

selected

ERROR

Invalid argument

S

Select Register

Selects a register for interrogation or modification in the current active profile. Subsequent reads or
writes to the register are accomplished with the

?

or

=

commands, respectively. The

S

command is

normally used with an appended ? or = . The register remains selected until the next

ATS

command.

The complete set of S-Registers is described in

Appendix E.

Format:

ATSn

Select register

<n>

Result codes:

OK

Valid register selected

ERROR

Unsupported register

«
...
148
149
150
151
152
...
»

Содержание DART 200















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DART 200

Бренд: ABB Страницы: 6

Бренд: Barracuda Страницы: 2

Бренд: ICP DAS USA Страницы: 38

Бренд: LandCell Страницы: 46

Бренд: AVM Страницы: 51

Бренд: DataComm Страницы: 39

Бренд: Vega Absolute Страницы: 23

Dolphin Navigan Wireless Commissioner NWC 300

Бренд: EnOcean Страницы: 9

Бренд: C-motech Страницы: 15

Бренд: NETGEAR Страницы: 19

Бренд: NETGEAR Страницы: 61

Бренд: Teledesign Страницы: 107

Бренд: Hughes Network Страницы: 4

Бренд: TP-Link Страницы: 2

Wiyana Connect 4g e-GO

Бренд: Zain Страницы: 6

Бренд: Racal-Vadic Страницы: 66

Бренд: Campbell Страницы: 28

Бренд: RadiSys Страницы: 66

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды