background image

9.2 

Control strategies and setpoints for 
controller 1, basic type A 

9.2.1 

Selecting the control strategy 

 

 
Controller 1 in basic type A is used for temperature control.  

Control strategies 
controller 1,  
basic type A 

Different control strategies are available.  
The following table shows the dependencies: 
 
 

Control strategy 
Explanations given in …

 

Required 
input 
identifiers 
Footnote 1

 

Connection 
inputs – 
control loop 
Footnote 2

 

Setting value 
STRATGY in 
CTLOOP 1

 

Room temperature control 
Subsection 9.2.6 
Footnote 3 

ROOM None  --- 

(No impact) 

Supply air temperature 
control 
Subsection 9.2.8 
Footnote 3 

SAT None --- 

(No impact) 

Changeover between room-
supply air temperature 
cascade control and supply 
air temperature control via a 
digital input 
Subsection 9.2.7 
Footnotes 4, 5, 6 

SAT 
ROOM 
DIG 

DIG -> 
CAS/CON 

CAS 
 

Room-supply air temperature 
cascade control 
Subsection 9.2.7 
Footnotes 5, 6 

SAT 
ROOM 

None CAS 

Room temperature control 
with supply air temperature 
limitation 
Subsection 9.2.9 
Footnotes 5, 6 

SAT 
ROOM 

None LIM 

 

Any input Xx of the input block can be used.  
Selection of an input identifier label requires that the respective temperature is indeed acquired 
(e.g. ROOM: (Room temperature must be available) 

The "connection" is made as a setting value in controller 1 block 

Setting value STRATGY has no impact in connection with room temperature and supply air 
temperature control.In these cases, the setting value is not evaluated 

CAS/CON facilitates changeover from cascade control in the summer to supply air temperature 
control in the winter (when heating is ON) via a digital input 

If both input identifiers SAT and ROOM are available, the STANDBY setting decides whether 
room-supply air temperature cascade control or room temperature control with supply air 
temperature limitation is performed 

If selection of a control strategy is required and none is selected ("---")  
- applies to room-supply air temperature cascade control and room temperature control with 
supply air temperature limitation – control strategy “Supply air temperature control”   
is automatically activated  

Explanations 

 

93 / 174 

Siemens 

Universal Controllers RLU2… 

CE1P3101en 

Building Technologies 

Controller (CTLOOP x) 

29.08.2008 

Содержание Synco 200















































































































































































Отзывы: