Siemens Synco 200 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 174

background image

2.5

Important notes

This symbol draws your attention to special safety notes and warnings. Failing to
observe these notes may result in injury and / or serious damage.

You may only use Synco™ 200 products to control and monitor heating, ventilation,
air conditioning and chilled water plants.

Field of use

Safe and trouble-free operation of Synco™ 200 products presupposes transport,
storage, mounting, installation and commissioning as intended as well as careful
operation.

Intended use

Fuses, switches, wiring and earthing must comply with local safety regulations for
electrical installations.

Electrical installation

Only qualified staff trained by Siemens BT may prepare and commission
Synco™ 200 products.

Commissioning

Only persons trained by Siemens BT or their representatives who are properly
informed of the risks may operate Synco™ 200 products.

Operation

When wiring, strictly separate AC 230 V mains voltage from AC 24 V safety extra-
low voltage (SELV) to protect against electrical shock!

Wiring

For storage and transport, the limits given in the relevant Data Sheets must always
be observed.

Storage and transport

Contact your supplier or Siemens BT if you have any questions.

Synco™ 200 products are maintenance-free and require only cleaning at regular
intervals. We recommend removing dust and dirt from system components
installed in the control panels during standard service.

Maintenance

Should system faults occur and you are not authorized to perform diagnostics and
rectify faults, call your Siemens BT service representative.

Faults

Only authorized staff are permitted to perform diagnostics, to rectify faults and to
restart the plant. This applies to working within the panel as well (e.g. testing or
changing fuses).

The devices contain electrical and electronic components and must not be
disposed of together with domestic waste.

Disposal

Local and currently valid legislation must be observed.

13 / 174

Siemens

Universal Controllers RLU2…

CE1P3101en

Building Technologies

Overview

29.08.2008

«
...
11
12
13
14
15
...
»

Содержание Synco 200















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Synco 200

Бренд: NEJE Страницы: 17

Бренд: Oceanic Страницы: 13

Бренд: Aalborg Страницы: 128

Бренд: Samson Страницы: 2

Бренд: Maestra Страницы: 22

Бренд: Patron Страницы: 36

Бренд: D&R ELECTRONICS Страницы: 12

963325-0403 - RumblePad 2 Vibration Feedback Gamepad Game Pad

Бренд: Logitech Страницы: 2

Бренд: Fuji Electric Страницы: 12

Бренд: heat-timer Страницы: 36

Бренд: ACL Страницы: 20

Бренд: Trane Technologies Страницы: 8

Бренд: Penn Страницы: 10

Бренд: Valence Tech Страницы: 12

Бренд: Dungs Страницы: 56

Бренд: Emec Страницы: 8

Бренд: bluelab Страницы: 39

Бренд: SOMFY Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды