Siemens Synco 200 Скачать руководство пользователя страница 131

Страница: 131 / 174

9.10 Universal setpoint shift

9.10.1 Activation

Universal setpoint shift is available with:

Controller 1,
basic type U,
controller 2

•

Controller 1, basic type U only

•

Controller 2

To activate the function, configure an appropriate input. You can only assign analog
inputs.

9.10.2 Operating principle

You can use a universal input to shift the controller's setpoint.

Function

Setpoint shift acts on the Comfort and Economy modes according to the following
diagram:

Diagram

SETCOOL

SETHEAT

[K]

CMP1END

CMP2END

CMP1STT

CMP2STT

CMP2D

CMP1D

Legend:

AI Analog

input

w Setpoint

shift

Typical applications for universal setpoint shift are:

Application

•

Refrigeration: Shifting the flow temperature setpoint for the chilled ceiling
according to room enthalpy or surface temperature

•

Ventilation: Shifting according to room humidity or surface temperature

9.10.3 Troubleshooting

When you leave the commissioning menu, the universal controller checks whether
a sensor is connected.

Sensor connected?

•

If, at that time, a sensor is connected, but is missing later, a sensor error
message is delivered and presented on the display:

–

"Xx ---"

=> sensor missing

–

"Xx ooo"

=> short-circuit

•

If, at that time, the sensor is not connected, setpoint compensation will be
deactivated

131 / 174

Siemens

Universal Controllers RLU2…

CE1P3101en

Building Technologies

Controller (CTLOOP x)

29.08.2008

Содержание Synco 200















































































































































































Результаты поиска

Содержание Synco 200

Отзывы:

Siemens Synco 200, Основная документация, Страница: 131 / 174

Результаты поиска

Содержание Synco 200

Отзывы: