Siemens Synco 200 Скачать руководство пользователя страница 86 | Manualshive

Страница: 86 / 174

background image

8.6.3

External preselection (IN X)

You can configure an analog input (IN X) as a preselection for the step switch. The
controller performs a maximum selection together with the internal signals.

Maximum selection in
case of several
preselections

For example, you can use this feature to implement the following function:
External control – the RLU236 provides the step switch function only.

The external signal is considered only if the controller operates in Comfort or
Economy mode.

Note

8.6.4

Output inversion (INVERS)

You can invert the step switch's analog output. Meaning:

Definition and behavior

INVERS = NO:

0…100% load = 0…100% output

INVERS = YES:

0…100% load = 100…0% output

The same settings are possible for this analog output as for the modulating output,
AO function block.
If the controller has a binary step switch and is switched off during operation (input
D1 = Protection), the output signal behaves as follows:
INVERS = NO:

0% output

INVERS = YES:

100% output

8.6.5

Function check / wiring test

The step switch can be switched directly via the control switch during the wiring
test.

Switching on / off

The switch has the following positions:

Switch positions

•

---

•

0…100 %

Settings such as INVERS, MIN POS and MAX POS are also effective during the
wiring test.

Note

The following priorities apply to the step switch:

Priorities

1 On / Off during the wiring test
2 According to the positioning signal from the sequence controller (preselection in

normal operation) or an external signal (maximum selection)

86 / 174

Siemens

Universal Controllers RLU2…

CE1P3101en

Building Technologies

Aggregates

29.08.2008

«
...
84
85
86
87
88
...
»

Содержание Synco 200















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Synco 200

Бренд: Febco Страницы: 4

Бренд: Cisco Страницы: 48

Бренд: Quinny Страницы: 29

Бренд: Quinny Страницы: 60

Бренд: Zennio Страницы: 30

Бренд: Zeta Страницы: 13

Бренд: V2 Страницы: 12

Бренд: H3C Страницы: 5

NORA-W10 Series

Бренд: u-blox Страницы: 56

Бренд: z21 Страницы: 2

Бренд: Vag Страницы: 15

Бренд: Full Gauge Controls Страницы: 3

Бренд: Velleman Страницы: 12

Бренд: National Instruments Страницы: 14

Бренд: BabyActive Страницы: 4

Бренд: Blue Point Engineering Страницы: 12

Бренд: ADLINK Technology Страницы: 37

Samos Pro Compact SP-COP2

Бренд: Wieland Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды