Siemens Synco 200 Скачать руководство пользователя страница 111

Страница: 111 / 174

Setpoint preselection

The following diagrams illustrate the different setpoint preselections for non-
changeover and changeover systems:

100 %

28 °C

21 °C

24 °C

19 °C

60 °C

40 °C

10 °C

6 °C

60 °C

21 °C

24 °C

100 %

0 %

SETHEAT

SETCOOL
SETCOOL

SETCOOL

SETHEAT

Sequence controller

Indirect
Heating

Direct
Cooling

Sequence controller

Indirect
Heating

Direct
Cooling

Non-changeover system:

Changeover system with basic type U:

Heating setpoints less than cooling setpoints
e.g. room temperature control

Heating setpoints greater than cooling
e.g. supply temperature control

Economy cooling setpoint

Economy heating setpoint

Comfort cooling setpoint

Comfort heating setpoint

Economy heating setpoint

Economy cooling setpoint
Comfort cooling setpoint

Refer to the corresponding setting values on the following page (factory settings).

Economy setpoints are only adjustable if an input has been defined for operating
mode changeover.

Note on Economy
setpoints

The following functions can have an influence on setpoints:

Influences on the
setpoints

•

Universal setpoint compensation (refer to section 9.10)

•

Remote setpoint, absolute (refer to section 7.4)

Sequence controller 2 always operates in the same mode as sequence controller
1, but it has no changeover functionality.

Basic type U,
controller 2

111 / 174

Siemens

Universal Controllers RLU2…

CE1P3101en

Building Technologies

Controller (CTLOOP x)

29.08.2008

Содержание Synco 200















































































































































































Результаты поиска

Содержание Synco 200

Отзывы:

Похожие инструкции для Synco 200

Бренды по названию

Популярные бренды

Siemens Synco 200, Основная документация

Результаты поиска

Содержание Synco 200

Отзывы:

Похожие инструкции для Synco 200

Бренды по названию

Популярные бренды