Siemens Synco 200 Скачать руководство пользователя страница 63

Страница: 63 / 174

8.3.3

Heat recovery changeover (TYPE)

To produce the changeover between HR equipment (wheel, glycol) and mixing
dampers, you can invert the output signal using TYPE.

Output inversion

You have to make the following settings in normal operation to achieve the
customary control response:

Settings

•

HR equipment:
\_

TYPE = ERC

0…100% load = 0…100% output

•

Mixing damper:
/_

TYPE = DMP

0…100% load = 100…0% output

This response applies if the HR equipment (HREC) is connected to the SEQ1 Y
heating sequence of the CTLOOP controller.

Note

If the controller with a HR equipment / mixing damper output is switched off during
operation (input D1 = Protection ), the output signal behaves as follows:

Output signal behavior

•

TYPE = ERC:

0% (i.e. DC 0 V)

•

TYPE = DMP:

0% (i.e. DC 0 V)

8.3.4

Limitations (MIN POS, MAX POS)

You can impose upper and lower limits on the modulating output.

Diagram

In that case, the 0…100% output signal corresponds to:
Minimum positioning signal (MIN POS)…maximum positioning signal (MAX POS).

0 %

100 %

0 %

0 V

100 %

10 V

MAX POS

MIN POS

Qs = load demand from the sequence controller

You can implement a minimum air damper position using the minimum positioning
signal (MIN POS).

Application example

The controller does not give consideration to MIN POS and MAX POS in Protection
mode.

Note

63 / 174

Siemens

Universal Controllers RLU2…

CE1P3101en

Building Technologies

Aggregates

29.08.2008

Содержание Synco 200















































































































































































Результаты поиска

Содержание Synco 200

Отзывы:

Siemens Synco 200, Основная документация, Страница: 63 / 174

Результаты поиска

Содержание Synco 200

Отзывы: