Siemens Synco 200 Скачать руководство пользователя страница 5

Страница: 5 / 174

1 About

this

document

1.1

Revision history

Against version 2.2 of this document, the following changes have been made:

Chapter/
section

Changes

All New

template

All

Controller RLU210 no longer mentioned in this document

All

Information about paths: CHK replaced by INFO

1 New

chapter

2.1 New

layout

2.4

New numbers; lines deleted; lines added

On displays and in reference texts:

•

New Info symbol

•

CHK is now

INFO

•

EXP is now PASS

•

New arrangement of the 9 navigation fields

3.2.1

Subsection "Example of Info page..." in table for Info level: One more
bullet added ("The pages are arranged…")

3.2.2

Subsection "Common properties": Last bullet: Time added

3.2.2

New: Subsection "Info pages at the service level" with examples

3.3.1

Subsection "Levels and menus" table cells for Info levels specified
more precisely

3.3.2 Table

revised

On displays and in reference texts:

•

New Info symbol

•

CHK is now

INFO

•

EXP is now PASS

•

New arrangement of the 9 navigation fields

4.3.2

Subsection Warning added

4.3.3 Note

added

4.4.1

Subsection HIT tool added

6.3

Text completely revised due to revised function

New input identifier SAT meaning supply air temperature

7.7.2

Subsection "Fault status signals" added

7.8

New section "Supply air temperature (SAT)" due to new function

8.1.2

Sentence added to subsection "On, after outside temperature”

8.1.2

New subsection "Pump kick"

8.1.5

As fourth priority with reference to pump kick

8.1.6

Line for kick added to table “Setting values”

8.2.2

New subsection "%OPEN according to the outside temperature”, with
notes

8.2.3

Text relating to caution and note added

8.2.5

2 lines relating to outside temperature-dependent on and opening
added to table in subsection "Setting values"

8.3.3 Note

added

5 / 174

Siemens

Universal Controllers RLU2…

CE1P3101en

Building Technologies

About this document

29.08.2008

Содержание Synco 200















































































































































































Результаты поиска

Содержание Synco 200

Отзывы:

Siemens Synco 200, Основная документация, Страница: 5 / 174

Результаты поиска

Содержание Synco 200

Отзывы: