manualshive.com logo in svg

Siemens Synco 200, Основная документация, Страница: 98 / 174

Поделиться
Скачать
Siemens Synco 200 Скачать руководство пользователя страница 98

9.2.7 

Implementation: Room-supply air temperature cascade 
controller 

9.2.7.1 

Activating the cascade controller 

 

 
The cascade controller can only be activated for controller 1, basic type A.  

Activation 

To activate room-supply air temperature cascade control, assign one input each to 
the room and the supply air temperature and select control strategy CAS.  
Also refer to subsection 9.2.1 ”Selecting the control strategy“. 
 
 
If, in addition, input CAS/CON is assigned to a terminal, this input must be "0" for 
cascade control. 

Function of CAS/CON 
input 

 
You can use this input to configure changeover of the control strategy between 
cascade and supply air temperature control: 

Note 

•

 

Cascade control  CAS/CON = 0 

•

 

Supply air temperature control 

CAS/CON = 1 (for behavior, refer to 

subsection 0) 

 
 

9.2.7.2 

Operating principle 

 

 
The following diagram shows the operating principle of room-supply air 
temperature cascade control: 

Principle 

 
 

T

T

TSu

TR

w

SpTSuC

SpTSuH

31

01

S

38

CTLOOP 1

PI

PID

 

 
 
The main controlled variable is the room temperature TR; the auxiliary controlled 
variable is the supply air temperature TSu. 
The room temperature controller provides PI control, the supply air temperature 
controller PID.  
The result is a PI+PID room-supply air temperature cascade control process. 
The room temperature controller sets the present setpoints SpTSuC and SpTSuH 
for the supply air temperature controller within the selected limit values. 

98 / 174 

 

Siemens 

Universal Controllers RLU2… 

CE1P3101en 

Building Technologies 

Controller (CTLOOP x) 

29.08.2008 

Содержание Synco 200















































































































































































Отзывы:

Нет отзывов