Siemens Simatic S7-1500 Скачать руководство пользователя страница 189

Страница: 189 / 402

Programming

7.5 Tracking active jobs

S7-1500 Motion Control V13 Update 3
Function Manual, 07/2014, A5E03879256-AC

189

7.5.3

Motion Control instructions without "Done" parameter

Description

Motion Control instructions without the "Done" parameter use a special parameter to achieve

the job target (e.g. "InVelocity", "InGear"). The target state or the movement is paused until

the job is canceled or an error occurs.
The following Motion Control instructions have a special parameter to display the job status:

●

MC_Power ( parameter "Status")

●

MC_MoveVelocity (parameter "InVeloctity")

●

MC_GearIn (parameter "InGear")

●

MC_MoveJog (parameter "InVelocity")
The special behavior of "MC_MoveJog" is described in the section Motion Control

Instruction MC_MoveJog (Page 193).

The behavior of the parameter is shown for various situations using the Motion Control

instruction "MC_MoveVelocity" as an example:

Example "MC_MoveVelocity"

An "MC_MoveVelocity" job is started with a positive edge at the "Execute" parameter. The

job objective is fulfilled when the assigned velocity is reached and the axis travels at

constant velocity. When the assigned velocity is reached and maintained, this is indicated in

the "InVelocity" parameter with the value TRUE.
The motion of the axis can, for example, be stopped with an "MC_Halt" job.

Содержание Simatic S7-1500



















































































































































































































































































































































































































Результаты поиска

Содержание Simatic S7-1500

Отзывы:

Похожие инструкции для Simatic S7-1500

Бренды по названию

Популярные бренды

Siemens Simatic S7-1500, Руководство по эксплуатации функций

Результаты поиска

Содержание Simatic S7-1500

Отзывы:

Похожие инструкции для Simatic S7-1500

Бренды по названию

Популярные бренды