Siemens SIMATIC NET TeleControl SINAUT ST7 Скачать руководство пользователя страница 13

Страница: 13 / 294

Table of contents

SINAUT ST7 station control system
System Manual, 09/2016, C79000-G8976-C178-10

5.3

GSM/GPRS modem MD720-3 .............................................................................................. 143

5.3.1

Displays and connectors ....................................................................................................... 144

5.3.2

Connecting the MD720-3 to the TIM and antenna ............................................................... 147

5.3.3

Prerequisites for operation .................................................................................................... 148

5.4

GPRS/GSM router MD741-1 ................................................................................................ 148

5.4.1

Displays and connectors ....................................................................................................... 149

5.4.2

Connecting the MD741-1 to the TIM and antenna ............................................................... 152

5.4.3

Prerequisites for operation .................................................................................................... 152

5.5

MD2 dedicated line modem .................................................................................................. 153

5.5.1

Displays and connectors accessible from the front .............................................................. 154

5.5.2

Configuration switches accessible from above ..................................................................... 160

5.5.3

Connectors and configuration switches accessible from below ........................................... 166

5.5.4

Connecting the MD2 with TIM, LTOP and dedicated line ..................................................... 169

5.6

LTOP line transformer with overvoltage protection .............................................................. 181

5.6.1

Structure ............................................................................................................................... 181

5.6.2

Connecting up the MD2 modem ........................................................................................... 183

5.7

Analog dial-up modem MD3 ................................................................................................. 186

5.7.1

Indicators and connectors accessible from the front ............................................................ 186

5.7.2

Configuration switches accessible from above ..................................................................... 193

5.7.3

Connectors and configuration switches accessible from below ........................................... 203

5.7.4

Connecting the MD3 with a TIM and TAE6 outlet ................................................................ 206

5.7.5

Connecting the MD3 with TIM, LTOP and dedicated line ..................................................... 207

5.7.6

User-configurable profiles ..................................................................................................... 213

5.7.7

LTOP line transformer with overvoltage protection .............................................................. 216

5.8

ISDN dial-up modem MD4 .................................................................................................... 217

5.8.1

Indicators and connectors accessible from the front ............................................................ 218

5.8.2

Configuration switches accessible from above ..................................................................... 223

5.8.3

Connectors and configuration switches accessible from below ........................................... 227

5.8.4

Connecting the MD4 with a TIM and ISDN outlet ................................................................. 229

5.9

Installing and putting a SINAUT MD2, MD3, MD4 modem into operation ............................ 230

5.9.1

Installation ............................................................................................................................. 230

5.9.2

Installation on an S7-300 rail ................................................................................................ 230

5.9.3

Installation on a 35 mm standard rail .................................................................................... 232

5.9.4

Horizontal and vertical installation ........................................................................................ 232

5.9.5

Connecting to the power supply ........................................................................................... 233

Technical specifications ...................................................................................................................... 235
6.1

Technical specifications of the TIM 3V-IE variants ............................................................... 235

6.2

Technical specifications of the TIM 4R-IE ............................................................................ 240

6.3

Technical specifications of the TIM 4 variants ...................................................................... 244

6.4

Current consumption and power loss of the SINAUT ST7 components .............................. 246

6.5

Technical specifications of the SINAUT ST7 modems ......................................................... 249

6.6

Technical specifications of the radio clock components ....................................................... 254

6.7

Technical specifications of the LTOP overvoltage protection module .................................. 257

Certifications and approvals ................................................................................................................ 259

Содержание SIMATIC NET TeleControl SINAUT ST7







































































































































































































































































































Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Похожие инструкции для SIMATIC NET TeleControl SINAUT ST7

Бренды по названию

Популярные бренды

Siemens SIMATIC NET TeleControl SINAUT ST7, Системное руководство

Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Похожие инструкции для SIMATIC NET TeleControl SINAUT ST7

Бренды по названию

Популярные бренды