Siemens SIMATIC NET TeleControl SINAUT ST7 Скачать руководство пользователя страница 155

Страница: 155 / 294

Installation and commissioning of the modems and routers

5.5 MD2 dedicated line modem

SINAUT ST7 station control system
System Manual, 09/2016, C79000-G8976-C178-10

155

LED displays of the MD2

The following table summarizes the meaning and activity of the six green LEDs on the front

of the modem.

Table 5- 9

Meaning and activity of the LEDs on the front of the MD2

LED no. Labeling

Description

TXD

Transmit data
The LED flashes in rhythm with the data flow sent to the modem and to

the WAN interface by the terminal device (for example TIM) over the RS-

232 or RS-485 interface.

RXD

Receive data
The LED flashes in rhythm with the data flow received by the modem

over the WAN interface and transferred to the terminal device (for exam-

ple TIM) over the RS-232 or RS-485 interface.

DTR

Data terminal ready
Indicates the status of the DTR signal of the connected terminal (for ex-

ample TIM). As soon as a terminal device has started up, it sets its DTR

signal to 1 after which the "DTR" LED on the MD2 is lit continuously.

RTS

Request to send (RTS)
Indicates the status of the RTS signal of the connected terminal (for ex-

ample TIM). When a terminal device turns on the transmitter of the mo-

dem, it sets its RTS signal to 1. As long as RTS is set to 1, the "RTS"

LED is lit on the MD2. The LED goes off as soon as the terminal device

deactivates the RTS signal.

CTS

Clear to send (CTS)
When the transmitter of the modem has been turned on by RTS, the

modem signals back to the terminal device (for example TIM) that it is

clear to send by setting its CTS signal to 1. As long as CTS is set to 1,

the "CTS" LED on the MD2 modem is lit. The LED goes off as soon as

the terminal device deactivates the RTS signal and turns off the transmit-

ter of the modem.

DCD/5V

Data carrier detect
The "DCD" LED lights up as soon as the internal operating voltage of the

MD2 modem is applied.
Whenever the MD2 detects an adequate receive level on its receive

channel, the "DCD" LED goes off.

Содержание SIMATIC NET TeleControl SINAUT ST7







































































































































































































































































































Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Похожие инструкции для SIMATIC NET TeleControl SINAUT ST7

Бренды по названию

Популярные бренды

Siemens SIMATIC NET TeleControl SINAUT ST7, Системное руководство

Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Похожие инструкции для SIMATIC NET TeleControl SINAUT ST7

Бренды по названию

Популярные бренды