Siemens SIMATIC NET TeleControl SINAUT ST7 Скачать руководство пользователя страница 201

Страница: 201 / 294

Installation and commissioning of the modems and routers

5.7 Analog dial-up modem MD3

SINAUT ST7 station control system
System Manual, 09/2016, C79000-G8976-C178-10

201

Profile no. Meaning

Setting on DIL switch

33600 bps (buffered)
(suitable only for RS-232 port)

AT mode
Freely configurable
(also suitable for RS-485 port)

Note
The selection of the standard dedicated line profile not only depends on the required

transmission speed but also on the interface to be used, the RS-232 or the RS-485 interface.

Standard dedicated line profiles 8 to 14 are only suitable for use with the RS-232 interface. If

you require the RS-485 interface, the user-configurable dedicated line profile 15 must be set

and configured. Profile 15 can, however, also be used with the RS-232 interface.

Loudspeaker ON or OFF
The MD3 modem is equipped with a loudspeaker. The loudspeaker allows you to hear all the

signal tones during the connection phase and during data transmission. The loudspeaker

can be turned on for test purposes or for normal operation.

Table 5- 33 Setting the loudspeaker

Loudspeaker

Setting on DIL switch

Turned off

Turned on

Modem reset
If the configuration of the modem is unclear, you can reset to the factory default settings.

When you reset the modem, all 16 standard profiles are reset to the default setting.
Procedure:
1.

Power supply OFF

Set switch SW2.7 to ON

Turn the power supply ON and then wait at least 10 seconds until the DCD LED lights up.

Содержание SIMATIC NET TeleControl SINAUT ST7







































































































































































































































































































Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Похожие инструкции для SIMATIC NET TeleControl SINAUT ST7

Бренды по названию

Популярные бренды

Siemens SIMATIC NET TeleControl SINAUT ST7, Системное руководство

Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Похожие инструкции для SIMATIC NET TeleControl SINAUT ST7

Бренды по названию

Популярные бренды