Siemens SIMATIC NET TeleControl SINAUT ST7 Скачать руководство пользователя страница 228

Страница: 228 / 294

Installation and commissioning of the modems and routers

5.8 ISDN dial-up modem MD4

SINAUT ST7 station control system

228

System Manual, 09/2016, C79000-G8976-C178-10

Pinout of the RJ-12 Western jack
The X3 connector of the MD4 modem is designed as a 6-pin RJ-12 Western jack. The pinout

is shown in the following table.

Table 5- 47 Pinout of the X3 RJ-12 jack for the MD4 modem

Illustration

Pin no.

Signal name

Signal direction

Remark

TX-

RX-

RX+

TX+

Standard connecting cable for the RJ-12 port
The connecting cable 6NH7700-4AR60 ships with every MD4 modem. This allows the

modem to be connected to an ISDN S

outlet.

The cable is no longer available as separate spare part.

Table 5- 48 Standard connecting cable for the MD4 modem

Order no.

Description

Illustration

6NH7700-4AR60

Connecting cable with RJ-12 and RJ-45 plug to con-

nect an MD4 modem (RJ-12) with an ISDN-S

jack (RJ-

45).

Cable length 6 m

Note
It is best to hold the cable just below the RJ-12 plug. This makes it easier to insert the plug

than if you hold the RJ-12 plug itself. When inserting it, make sure that you can hear the RJ-

12 connector click into place!

Содержание SIMATIC NET TeleControl SINAUT ST7







































































































































































































































































































Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Похожие инструкции для SIMATIC NET TeleControl SINAUT ST7

Бренды по названию

Популярные бренды

Siemens SIMATIC NET TeleControl SINAUT ST7, Системное руководство

Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Похожие инструкции для SIMATIC NET TeleControl SINAUT ST7

Бренды по названию

Популярные бренды