Siemens SIMATIC NET TeleControl SINAUT ST7 Скачать руководство пользователя страница 193

Страница: 193 / 294

Installation and commissioning of the modems and routers

5.7 Analog dial-up modem MD3

SINAUT ST7 station control system
System Manual, 09/2016, C79000-G8976-C178-10

193

5.7.2

Configuration switches accessible from above

The following figure shows the MD3 modem from above. It indicates the location of the SW1

(4-pin) and SW2 (10-pin) DIL switches that are accessible from above.

Figure 5-29 View of the MD3 modem from above

Settings with the DIL switches accessible from above
The MD3 modem has a 4-pin and a 10-pin DIL switch. The 10-pin DIL switch, SW2 is

located directly on the top housing grill. The 4-pin DIL switch, SW1, can also be reached

from above through the housing grill, however it is located deeper within the housing and

may therefore be more difficult recognize. To set this switch, you require a long, thin tool, for

example a small screwdriver or a toothpick.
The DIL switches have the following functions:

●

4-pin DIL switch SW1
–

Metering pulse filter

at 12 kHz or at 16 kHz

–

Activating or deactivating the loop power section

Содержание SIMATIC NET TeleControl SINAUT ST7







































































































































































































































































































Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Похожие инструкции для SIMATIC NET TeleControl SINAUT ST7

Бренды по названию

Популярные бренды

Siemens SIMATIC NET TeleControl SINAUT ST7, Системное руководство

Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Похожие инструкции для SIMATIC NET TeleControl SINAUT ST7

Бренды по названию

Популярные бренды