Siemens SIMATIC NET TeleControl SINAUT ST7 Скачать руководство пользователя страница 85

Страница: 85 / 294

SINAUT ST7 station control system
System Manual, 09/2016, C79000-G8976-C178-10

Installation guide

3.1

Installing the TIM 3V-IE variants in an S7-300

Introduction

The TIM 3V-IE variants can be used in an S7-300 as communications processors (CP). In

principle, all S7-300 standard and compact CPUs can be combined with these TIMs. There

are, however, constraints that must be taken into account relating to the way in which data

exchange between the TIM and the CPU in the rack is handled (the SINAUT program). For

the TIM 3V-IE variants, there are two options:
1.

TD7onTIM
This SINAUT TD7 program runs on the TIM.
All standard and compact CPUs can be used without restrictions.

TD7onCPU
This SINAUT TD7 program runs on the CPU and is created for the CPU with blocks from

the SINAUT TD7 library.
In this case, only CPUs with a work memory adequate to accommodate the SINAUT

program can be used. The size of the program depends on the amount of data to be

transmitted. At least 20 Kbytes are required. TD7onCPU can be used for several

standard CPU types if the following software packages are used:
–

"SINAUT TD7 library for the CPU" as of V2.2

–

"TIM firmware" as of V1.2

The following CPU lists also include older CPU types that can no longer be ordered as new

devices but that nevertheless may still be in use in the field. These are shown in

parentheses.

Standard CPU type

As of article number

CPU 312

6ES7 312-1AD10-0AB0

6ES7 312-1AE13-0AB0

6ES7 312-1AE14-0AB0

CPU 312 IFM

6ES7 312-5AC00-0AB0

6ES7 312-5AC02-0AB0

CPU 313

6ES7 313-1AD00-0AB0

6ES7 313-1AD01-0AB0

6ES7 313-1AD02-0AB0

6ES7 313-1AD03-0AB0

Содержание SIMATIC NET TeleControl SINAUT ST7







































































































































































































































































































Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Похожие инструкции для SIMATIC NET TeleControl SINAUT ST7

Бренды по названию

Популярные бренды

Siemens SIMATIC NET TeleControl SINAUT ST7, Системное руководство

Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Похожие инструкции для SIMATIC NET TeleControl SINAUT ST7

Бренды по названию

Популярные бренды