Siemens SIMATIC NET TeleControl SINAUT ST7 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 294

background image

Properties of the SINAUT components

1.3 Properties of the TIM modules

SINAUT ST7 station control system

18

System Manual, 09/2016, C79000-G8976-C178-10

TIM 3V-IE / TIM 3V-IE Advanced

The TIM 3V-IE is a SINAUT communications module for the SIMATIC S7-300. It has an RS-

232 interface to which a suitable modem can be connected. It also has an RJ-45 interface

that allows SINAUT communication over IP-based networks (LAN or WAN).
The TIM 3V-IE is available in a standard and advanced version:

●

TIM 3V-IE
With the TIM 3V-IE either the Ethernet interface or the RS-232 interface can be used for

the SINAUT communication.

●

TIM 3V-IE Advanced
With the TIM 3V-IE Advanced, the two interfaces can be used at the same time for

SINAUT communication. The two transmission paths can be completely independent of

each other or form a redundant transmission path.

Note
Low cycle monitoring time of the CPU
If the cycle monitoring time of the CPU is set to very low values, for example 1 ms, this can

lead to malfunctions on the TIM 3V-xxx. In this case, increase the cycle monitoring time of

the CPU or use a TIM 4R-xxx.

TIM 4R-IE

The TIM 4R-IE is suitable for installation in a SIMATIC S7-300 as a communications module

and can also be connected over Ethernet to one or more SIMATIC S7-400s and to ST7cc or

ST7sc PC control centers as a standalone device.
It has two combined RS-232/RS-485 interfaces to which a classic WAN (dedicated line or

dial-up network) can be connected via a suitable modem. It also has two RJ-45 interfaces

that allow SINAUT communication over Ethernet-based networks (LAN or WAN).
All four interfaces can be used at the same time for SINAUT communication. The four

transmission paths can all be different and operated independently. The two pairs of

interfaces can also form a redundant transmission path.

TIM 4

The TIM 4 is suitable for installation in the SIMATIC S7-300 as a communications module

and can also be connected via their MPI ports to one or more SIMATIC S7-300/-400s and to

ST7cc or ST7sc PC control centers as a standalone device.
It has two WAN connectors in the form of RS-232/RS-485 ports to which a suitable external

modem can be connected.
The two WANs that can be connected to a TIM 4 may be of the same type or different, for

example dedicated line plus telephone network. The two transmission paths can be either

completely independent of each other or form a redundant transmission path.
The TIM 4RD is equipped with a DCF77 radio clock receiver.

«
...
16
17
18
19
20
...
»

Содержание SIMATIC NET TeleControl SINAUT ST7







































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SIMATIC NET TeleControl SINAUT ST7

Evolution Series E9000

Бренд: GE Страницы: 44

PACSystems RX7i

Бренд: GE Страницы: 469

GuardSwitch 300 Series

Бренд: GE Страницы: 2

GuardSwitch 300 Series

Бренд: GE Страницы: 2

Masoneilan VariPak 28001

Бренд: GE Страницы: 24

Бренд: Zolix Instruments Страницы: 22

Бренд: Samson Страницы: 56

Бренд: Hach Страницы: 128

Бренд: Yamato Страницы: 33

Бренд: Xantrex Страницы: 56

Бренд: Xantrex Страницы: 2

Freedom Sequence

Бренд: Xantrex Страницы: 58

Бренд: Xantrex Страницы: 4

Бренд: Xantrex Страницы: 20

Бренд: Zamel Страницы: 2

Бренд: KanDao Страницы: 265

Бренд: Texas Instruments Страницы: 25

Wattstopper LMIN-104

Бренд: LEGRAND Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды