Siemens SIMATIC NET TeleControl SINAUT ST7 Скачать руководство пользователя страница 133

Страница: 133 / 294

Installing and putting a TIM into operation

4.5 Configuration

SINAUT ST7 station control system
System Manual, 09/2016, C79000-G8976-C178-10

133

Figure 4-4

Connecting TIM 3V-IE variants and the TIM 4R-IE to the power supply

Note
If one or more TIMs are installed as a CP in an S7-300 device, the CPU and TIMs must be

connected to the same power supply. This ensures that the CPU and TIMs start up at the

same time when the power supply is turned on.

4.5

Configuration

Configuring the TIM

In volume 2 "Software" of the SINAUT ST7 system manual, you will find a detailed

description of configuring the TIM. Configuration and loading the configuration data on the

station are necessary to obtain an operable TIM.

4.6

Startup activities of the TIM module

4.6.1

Startup of the TIM 3V-IE variants

Introduction

During startup, the LEDs on the front panel of the TIM 3V-IE variants have a different

significance than during normal operation. They are optical indicators of the various startup

phases and provide detailed information about any errors detected during startup. The only

exceptions are the LINK and RX/TX LEDs that have no significance during the startup of the

TIM 3V-IE variants.

Содержание SIMATIC NET TeleControl SINAUT ST7







































































































































































































































































































Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Похожие инструкции для SIMATIC NET TeleControl SINAUT ST7

Бренды по названию

Популярные бренды

Siemens SIMATIC NET TeleControl SINAUT ST7, Системное руководство

Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Похожие инструкции для SIMATIC NET TeleControl SINAUT ST7

Бренды по названию

Популярные бренды