Siemens SIMATIC NET TeleControl SINAUT ST7 Скачать руководство пользователя страница 213

Страница: 213 / 294

Installation and commissioning of the modems and routers

5.7 Analog dial-up modem MD3

SINAUT ST7 station control system
System Manual, 09/2016, C79000-G8976-C178-10

213

Attenuation values of the MD3 modem in dedicated line mode

Table 5- 38 Attenuation values of the MD3 modem in dedicated line mode

Transmission speed (bps)

Attenuation per km

(dB)

Attenuation per LTOP

(dB)

with cable termination where Z = Zr
300 to 33600

1.0

0.4

Maximum range of the MD3 modem in dedicated line mode

Table 5- 39 Maximum range of the MD3 modem in dedicated line mode

Transmission

speed (bps)

maximum range (km)

Transmission level –15 dB

Transmission level –-10 dB

with LTOP

without LTOP

with LTOP

without LTOP

with cable termination where Z = Zr
300

1200 to 19200

33600

The values shown in the table are guide values for a message line of the type 2 x 2 x 0,8 J-

Y(St)Y (non-coil-loaded line).
When determining the maximum ranges, a level reserve of 4 dB was included. This was

intended to ensure that even when fluctuations in the cable properties occurred, that

experience shows do occur during operation, there was still an adequate level for

undisturbed data transmission.

5.7.6

User-configurable profiles

Introduction

Apart from the 7 standard profiles for dial-up mode (profile 0 to 6) and dedicated line mode

(profile 8 to 14), the MD3 modem makes a freely configurable profile available for every

mode. Profile 7 is freely configurable profile for dial-up mode, profile 15 for dedicated line

mode.
The configuration of both profiles is performed by a PC using At commands. To do this, the

PC and modem are connected to each other via a cable. On the PC the connecting cable is

connected to COM1 or COM2, on the modem via the RS-232 interface.
The AT commands are transferred by a terminal program. Hyper-Terminal of WINDOWS is

suitable for this.

Connection between PC and modem
To transfer the AT commands, the connection is established between the PC and modem

with the SINAUT ST7 standard cable 6NH7701-4AL. If the standard cable is not available, a

Содержание SIMATIC NET TeleControl SINAUT ST7







































































































































































































































































































Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Похожие инструкции для SIMATIC NET TeleControl SINAUT ST7

Бренды по названию

Популярные бренды

Siemens SIMATIC NET TeleControl SINAUT ST7, Системное руководство

Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Похожие инструкции для SIMATIC NET TeleControl SINAUT ST7

Бренды по названию

Популярные бренды