Siemens SIMATIC NET TeleControl SINAUT ST7 Скачать руководство пользователя страница 126 | Manualshive

Страница: 126 / 294

background image

Installing and putting a TIM into operation

4.4 Installing a TIM

SINAUT ST7 station control system

126

System Manual, 09/2016, C79000-G8976-C178-10

4.4

Installing a TIM

4.4.1

Important notes on using the device

Safety notices on the use of the device

The following safety notices must be adhered to when setting up and operating the device

and during all work relating to it such as installation, connecting up, replacing devices or

opening the device.

General notices

WARNING

Safety extra low voltage
The equipment is designed for operation with Safety Extra-Low Voltage (SELV) by a

Limited Power Source (LPS).
This means that only SELV / LPS complying with IEC 60950-1 / EN 60950-1 / VDE 0805-1

must be connected to the power supply terminals. The power supply unit for the equipment

power supply must comply with NEC Class 2, as described by the National Electrical Code

(r) (ANSI / NFPA 70).
There is an additional requirement if devices are operated with a redundant power supply:
If the equipment is connected to a redundant power supply (two separate power supplies),

both must meet these requirements.

WARNING

Opening the device
DO NOT OPEN WHEN ENERGIZED.

The following notices relate to the following modules:

●

TIM 3V-IE

●

TIM 3V-IE Advanced

●

TIM 4R-IE

Please note the following notices when using these modules in a hazardous location.

«
...
124
125
126
127
128
...
»

Содержание SIMATIC NET TeleControl SINAUT ST7







































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SIMATIC NET TeleControl SINAUT ST7

Бренд: Warner Electric Страницы: 3

Бренд: iCeeO2 Страницы: 7

Бренд: SABAF Страницы: 6

COOPER POWER SERIES

Бренд: Eaton Страницы: 50

Бренд: Warren Controls Страницы: 28

Бренд: EAS Electric Страницы: 89

Бренд: Madas Страницы: 6

Бренд: Madas Страницы: 11

Бренд: Parker Страницы: 12

Бренд: RADVision Страницы: 3

Бренд: RADEMACHER Страницы: 48

Бренд: R&M Страницы: 53

Бренд: WAGO Страницы: 18

Бренд: WAGO Страницы: 46

Бренд: Balboa Water Group Страницы: 88

Бренд: ABB Страницы: 2

Бренд: Newport Страницы: 417

Бренд: Mitsubishi Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды