Siemens SIMATIC NET TeleControl SINAUT ST7 Скачать руководство пользователя страница 249

Страница: 249 / 294

Technical specifications

6.5 Technical specifications of the SINAUT ST7 modems

SINAUT ST7 station control system
System Manual, 09/2016, C79000-G8976-C178-10

249

6.5

Technical specifications of the SINAUT ST7 modems

Technical specifications of the MD2 dedicated line modem

MD2

Interfaces

•

Attachment to dedicated line

•

RS-232 attachment to DTE

•

RS-485 attachment to DTE

•

Connection to power supply

•

RJ-12

•

9-pin D-sub male connector

•

9-pin D-sub female connector

•

4-pin terminal strip

Power supply

24 V DC

Current consumption

•

From 24 V DC

•

100 mA

Power loss

2.4 W

Permitted ambient conditions

•

Operating temperature

•

Transport/storage temperature

•

Relative humidity

•

0 °C t60 °C

•

-40 °C t70 °C

•

Max. 95 % at +25 °C

Construction

•

Module format

•

Dimensions (W x H x D) in mm

•

Weight

•

Compact module for S7-300, double width

•

80 x 125 x 120

•

Approx. 300 g

Degree of protection

IP 20

Transmission path

2-wire, 2 x 2-wire or 4-wire,

twisted pair, without loading coils or with few

loading coils

Type of modulation

•

Frequency shift keying (FSK)

Transmission speeds

•

1200 bps

•

2400 bps

•

9600 bps (not for telephone company

leased lines)

•

19,200 bps (not for telephone company

leased lines)

Mode

•

With 2-wire or 2 x 2-wire

•

With 4-wire

•

Half duplex

•

Duplex or half duplex

Transmit level can be set to

•

0 dB

•

-6 dB

•

-9 dB (for telephone company leased lines)

•

-15 dB

Содержание SIMATIC NET TeleControl SINAUT ST7







































































































































































































































































































Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Похожие инструкции для SIMATIC NET TeleControl SINAUT ST7

Бренды по названию

Популярные бренды

Siemens SIMATIC NET TeleControl SINAUT ST7, Системное руководство

Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Похожие инструкции для SIMATIC NET TeleControl SINAUT ST7

Бренды по названию

Популярные бренды