Siemens SIMATIC NET TeleControl SINAUT ST7 Скачать руководство пользователя страница 254

Страница: 254 / 294

Technical specifications

6.6 Technical specifications of the radio clock components

SINAUT ST7 station control system

254

System Manual, 09/2016, C79000-G8976-C178-10

6.6

Technical specifications of the radio clock components

Technical specifications of DCF77 antennas

Table 6- 3

Technical specifications of DCF77 antennas

DCF77 antennas

Article numbers

6NH9831-0AA, 6NH9831-0BA, 6NH9831-0DA

General

Power supply (over antenna cable)

1.7 to 5 V DC

Impedance

50 ohms

Power gain

20 dB

Max. cable length without amplification

250 m

Plastic housing

Light-resistant

Bandwidth

4 kHz

Indoor antennas

Humidity

95% no condensation

Degree of protection

IP50

Temperature range

•

Operation

•

Storage

•

0 °C to +80 °C

•

-50 °C to +85 °C

Outdoor antennas

Wind load

max. 180 km/h

Degree of protection

IP65

Temperature range

•

Operation

•

Storage

•

-30 °C to +80 °C

•

-50 °C to +85 °C

Humidity

100%

Table 6- 4

Technical specifications of indirect lightning protection

DCF77 antennas

Article numbers

6NH9831-2AA, 6NH9831-8LA

Lightning protection

Housing material

Die cast aluminum housing

Dimensions (W x H x D) in mm

250 x 105 x 95

Weight

Approx. 3.5 kg

Grounding point

•

Thickness of copper strand

•

length of copper strand

M6 threaded connection

•

min. 10 mm2

•

max. 10 m

Current pulse withstand 8/20 µs wave

10 kA

Содержание SIMATIC NET TeleControl SINAUT ST7







































































































































































































































































































Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Похожие инструкции для SIMATIC NET TeleControl SINAUT ST7

Бренды по названию

Популярные бренды

Siemens SIMATIC NET TeleControl SINAUT ST7, Системное руководство

Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Похожие инструкции для SIMATIC NET TeleControl SINAUT ST7

Бренды по названию

Популярные бренды