Siemens SIMATIC NET TeleControl SINAUT ST7 Скачать руководство пользователя страница 117

Страница: 117 / 294

Installation guide

3.5 Standalone TIM 4 with an S7-400 or PC

SINAUT ST7 station control system
System Manual, 09/2016, C79000-G8976-C178-10

117

Example of configurations with the SINAUT ST7cc or ST7sc control center systems

The SINAUT ST7cc control center system based on WinCC or the SCADA Connect

Software SINAUT ST7sc is connected to the SINAUT telecontrol network just as with an S7-

400 over one or more TIM 4 modules. These TIMs are connected to the MPI adapter of the

SINAUT ST7cc / ST7sc system over their MPI interface. The inclusion of a telecontrol

master, for example an S7-400 is not necessary. Data exchange with the stations is handled

by the master TIM 4 modules.
The following figure shows the simplest configuration for a SINAUT ST7cc or ST7sc control

center system with one (1) connection to a WAN.

Figure 3-21 SINAUT ST7cc / ST7sc control center systems with TIM 4 on MPI bus,

1 connection to WAN via MDx modem

In much the same way as with an S7-400, ST7cc / ST7sc can also have two connections to

a WAN. The following figure shows the configuration.

Содержание SIMATIC NET TeleControl SINAUT ST7







































































































































































































































































































Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Похожие инструкции для SIMATIC NET TeleControl SINAUT ST7

Бренды по названию

Популярные бренды

Siemens SIMATIC NET TeleControl SINAUT ST7, Системное руководство

Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Похожие инструкции для SIMATIC NET TeleControl SINAUT ST7

Бренды по названию

Популярные бренды