Siemens SIMATIC NET TeleControl SINAUT ST7 Скачать руководство пользователя страница 58

Страница: 58 / 294

Properties of the SINAUT components

1.5 Mobile wireless components

SINAUT ST7 station control system

System Manual, 09/2016, C79000-G8976-C178-10

1.5.2

Antennas

The ANT794-4MR GSM/GPRS antenna

The following antennas are available for use in GSM/GPRS networks and can be installed

both indoors and outdoors. The antennas must be ordered separately.

●

Quadband antenna ANT794-4MR
You will find detailed information in the device manual. You will find this on the Internet on

the pages of Siemens Industrial Automation Customer Support under the following entry

ID:
16518558 (

http://support.automation.siemens.com/WW/view/en/16518558

)

Figure 1-33 ANT794-4MR GSM/GPRS antenna

Short name

Order no.

Explanation

ANT794-4MR

6NH9 860-1AA00

Quadband antenna (900, 1800/1900 MHz, UMTS);

weatherproof for indoor and outdoor areas; 5 m

connecting cable connected permanently to the

antenna; SMA connector, including installation

bracket, screws, wall plugs

●

Flat antenna ANT794-3M

Figure 1-34 Flat antenna ANT794-3M

Short name

Order no.

Explanation

ANT794-3M

6NH9 870-1AA00

Flat antenna (900, 1800/1900 MHz); weatherproof

for indoor and outdoor areas; 1.2 m connecting cable

connected permanently to the antenna; SMA con-

nector, including adhesive pad, screws mounting

possible

Содержание SIMATIC NET TeleControl SINAUT ST7







































































































































































































































































































Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Похожие инструкции для SIMATIC NET TeleControl SINAUT ST7

Бренды по названию

Популярные бренды

Siemens SIMATIC NET TeleControl SINAUT ST7, Системное руководство

Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Похожие инструкции для SIMATIC NET TeleControl SINAUT ST7

Бренды по названию

Популярные бренды