Siemens SIMATIC NET TeleControl SINAUT ST7 Скачать руководство пользователя страница 139

Страница: 139 / 294

Installing and putting a TIM into operation

4.6 Startup activities of the TIM module

SINAUT ST7 station control system
System Manual, 09/2016, C79000-G8976-C178-10

139

Phase

Activity

Explanation

Service mode

After all the LEDs have gone off, all LEDs light up again for 5 seconds. During this time,

the user can force a default startup (see below) using the reset button. Otherwise, the

TIM changes to phase 4.

Software startup

All the LEDs go off again and then light up again one after the other starting with LED 2

(TXD). At this stage of startup, the individual steps of the software startup are signaled

by the LEDs. The LEDs are either lit continuously or flash. The following table lists the

exact meaning of the individual LEDs when lit continuously or flashing during this

startup phase 4.

Startup completed

The LEDs go off if phase 4 is completed free of errors and then have the significance

according to their definition in normal operation.

Table 4- 12 LED activity during software startup (startup phase 4)

Phase

Activity

LED 2

LED 3

LED 4

LED 5

LED 6

4.1

Starting the RMOS operating system

4.2

Starting the TIM firmware

(On)

4.3

Start normal startup

(On)

Start default startup

(On)

Flashes

4.4

Startup of the TIM as CP in the S7-300 rack

(On)

(On/flashes)

Startup of the TIM on MPI (TIM 4 only)

(On)

(On/flashes)

Flashes

4.5

Normal startup with parameters

(On)

(On/flashes)

Normal startup without parameters

(On)

(On/flashes) Flashes

Default startup

(On)

Flashes

(On/flashes) Flashes

The LEDs whose activity is not shown in brackets ( ), provide the actual information on the

current startup phase.

Group error LED

If an error occurs during startup, the red group error LED (SF) lights up and, if the TIM 4 is

installed as a CP in an S7-300 rack, a diagnostic interrupt is sent to the CPU. A message to

this effect is also entered in the diagnostic buffer of the TIM 4. In the chapter on the SINAUT

Diagnostics and Service tool, you will find a table with a summary of all the errors that can

cause the group error LED to light up, as well as a detailed description of each error

message.

Note
After transferring the SDBs to the TIM, the group error LED flashes for approximately 10

seconds. This indicates that the TIM has registered the transfer and will automatically start a

reset after a further 10 seconds and the parameter assignment from the newly transferred

SDBs will be adopted. The TIM then behaves the same as following power "ON".

Содержание SIMATIC NET TeleControl SINAUT ST7







































































































































































































































































































Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Похожие инструкции для SIMATIC NET TeleControl SINAUT ST7

Бренды по названию

Популярные бренды

Siemens SIMATIC NET TeleControl SINAUT ST7, Системное руководство

Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Похожие инструкции для SIMATIC NET TeleControl SINAUT ST7

Бренды по названию

Популярные бренды