Siemens SIMATIC NET TeleControl SINAUT ST7 Скачать руководство пользователя страница 239

Страница: 239 / 294

Technical specifications

6.1 Technical specifications of the TIM 3V-IE variants

SINAUT ST7 station control system
System Manual, 09/2016, C79000-G8976-C178-10

239

TIM 3V-IE Advanced

Local communication

•

Over backplane bus with the S7-300-CPU

•

Over backplane bus with other TIMs in the

rack

•

Over MPI port of the S7-300-CPU

with other

CPUs, TIMs, and/or PCs

•

Over Ethernet interface with CPUs, PCs and

other TIMs

•

Possible over TD7onCPU and

TD7onTIM

•

Possible

•

Possible over TD7onCPU (for S7-300 and

S7-400) and S7 communication (for

ST7cc/ST7sc and TIMs)

•

Possible over TD7onCPU (for S7-400) and S7

communication (for ST7cc/ST7sc and TIMs)

Work memory required on the S7 CPU

•

SINAUT TD7 on CPU (TD7onCPU)

•

SINAUT TD7 on TIM (TD7onTIM)

•

At least 20 KB; actual requirements depend

on the amounts of data and range of functions

•

Best case, 0 bytes

Message memory on TIM

•

Number of messages

•

Buffered

•

32,000 messages

•

Transmission protocols (RS-232)

Selectable protocols

•

SINAUT ST7

•

SINAUT ST1

Mode with dedicated line/wireless network

•

SINAUT ST7 protocol

•

SINAUT ST1 protocol

•

Modes:
–

Polling

–

Polling with time slots

–

Multi-master polling with time slots

•

Modes:
–

Polling

–

Polling with time slots

Mode in dial-up network

•

SINAUT ST7 protocol

•

GPRS/MSC tunnel on the basis of the

SINAUT ST7 protocol

•

SINAUT ST1 protocol

•

Spontaneous

•

Spontaneous

•

Spontaneous

Asynchronous character format

•

SINAUT ST7 protocol, polling or

spontaneous

•

SINAUT ST7 protocol,

multi-master polling

•

SINAUT ST1 protocol, polling

•

SINAUT ST1 protocol, spontaneous

•

10 or 11 bits

•

10 bits

•

11 bits

•

10 or 11 bits

Содержание SIMATIC NET TeleControl SINAUT ST7







































































































































































































































































































Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Похожие инструкции для SIMATIC NET TeleControl SINAUT ST7

Бренды по названию

Популярные бренды

Siemens SIMATIC NET TeleControl SINAUT ST7, Системное руководство

Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Похожие инструкции для SIMATIC NET TeleControl SINAUT ST7

Бренды по названию

Популярные бренды