Siemens SIMATIC NET TeleControl SINAUT ST7 Скачать руководство пользователя страница 232

Страница: 232 / 294

Installation and commissioning of the modems and routers

5.9 Installing and putting a SINAUT MD2, MD3, MD4 modem into operation

SINAUT ST7 station control system

232

System Manual, 09/2016, C79000-G8976-C178-10

5.9.3

Installation on a 35 mm standard rail

To mount the modem on a 35 mm standard mounting rail, use the separately available

adapter 6NH7760-0AA.

Figure 5-55 Adapter for mounting on a 35 mm standard rail

Hang the modem on the adapter in much the same way as when mounting the modem on an

S7-300 rail. Screw the modem to the adapter. It is now prepared for mounting on a standard

mounting rail and can be snapped onto it.
For the remaining mounting procedure continue as described in the section Mounting on an

S7-300 standard mounting rail.

5.9.4

Horizontal and vertical installation

A SINAUT modem can be operated both in a horizontal and in a vertical installation.

Содержание SIMATIC NET TeleControl SINAUT ST7







































































































































































































































































































Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Похожие инструкции для SIMATIC NET TeleControl SINAUT ST7

Бренды по названию

Популярные бренды

Siemens SIMATIC NET TeleControl SINAUT ST7, Системное руководство

Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Похожие инструкции для SIMATIC NET TeleControl SINAUT ST7

Бренды по названию

Популярные бренды