Siemens SIMATIC NET TeleControl SINAUT ST7 Скачать руководство пользователя страница 67

Страница: 67 / 294

Properties of the SINAUT components

1.8 Connecting cables

SINAUT ST7 station control system
System Manual, 09/2016, C79000-G8976-C178-10

Order no.

Description

Illustration

6NH1701-7AN

Cable for connecting a TIM 11 (RS-232) with one of the SINAUT ST7

MD2, MD3 or MD4 modems (RS-232).

Cable length 2.5 m

6NH1701-7BK

Cable for connecting a TIM011B (RS-232) with one of the SINAUT ST7

MD2, MD3 or MD4 modems (RS-232).

Cable length 1.0 m.

1.8.2

Cables for the WAN connection of the modems

A 6NH7700-xxx connecting cable ships with every MDx modem. This can be used to

connect the modem to the relevant WAN network.

Table 1- 23 Cables for the WAN connection of the modems

Order no.

Description

Illustration

6NH7700-2AR60

Connecting cable with 2 x RJ-12 plugs for connection to an

MD2 modem (RJ-12) with an LTOP overvoltage protection

module (RJ-12).

Cable length 6 m
The adapter cable is no longer available as separate spare

part.

6NH7700-3BR60

Connecting cable with 2 x RJ-12 Western plug and snap-

on TAE6N plug to connect an MD3 modem (RJ-12) to a

telephone jack (TAE6N) or an LTOP overvoltage protection

module (RJ-12) if the MD3 modem is being operated as a

dedicated line modem.

Cable length 6 m
The adapter cable is no longer available as separate spare

part.

6NH7700-4AR60

Connecting cable with RJ-12 and RJ-45 plug to connect an

MD4 modem (RJ-12) with an ISDN-S

jack (RJ-45).

Cable length 6 m
The adapter cable is no longer available as separate spare

part.

Содержание SIMATIC NET TeleControl SINAUT ST7







































































































































































































































































































Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Похожие инструкции для SIMATIC NET TeleControl SINAUT ST7

Бренды по названию

Популярные бренды

Siemens SIMATIC NET TeleControl SINAUT ST7, Системное руководство

Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Похожие инструкции для SIMATIC NET TeleControl SINAUT ST7

Бренды по названию

Популярные бренды