Siemens SIMATIC NET TeleControl SINAUT ST7 Скачать руководство пользователя страница 183

Страница: 183 / 294

Installation and commissioning of the modems and routers

5.6 LTOP line transformer with overvoltage protection

SINAUT ST7 station control system
System Manual, 09/2016, C79000-G8976-C178-10

183

Dedicated line (screw terminals 1, 2, 5, 6)

Chassis (screw terminals 3, 4)

Modem attachment 2-wire over screw terminals

X2 + X3

Modem attachment 4-wire over screw terminals

2-wire/4-wire modem attachment over RJ-12 Western connector; for direct connection of

the SINAUT ST7 MD2 modem over the standard connecting cable (RJ-12 – RJ-12) that

ships with this modem.

S1 + S2

Configuration switches

View from above

Schematic

5.6.2

Connecting up the MD2 modem

The following figures show the connection of the standard cable modem MD2-3. The

connection to the LTOP1 or LTOP2 is via the standard cable that ships with the modem. This

cable has RJ-12 Western plugs at both ends.
Please make sure that the MD2-3 modem has the correct line termination setting:

●

For end point 1200 or 2400 bps: 600 ohms

●

For end point 19,200 bps: 150 ohms

●

For a tapping point: High resistance

Note
Please make sure that the S1 and S2 switches are set correctly in position 1 or 2 as shown

in the following figures!

Содержание SIMATIC NET TeleControl SINAUT ST7







































































































































































































































































































Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Бренды по названию

Популярные бренды

Siemens SIMATIC NET TeleControl SINAUT ST7, Системное руководство

Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Бренды по названию

Популярные бренды