Siemens SIMATIC NET TeleControl SINAUT ST7 Скачать руководство пользователя страница 233

Страница: 233 / 294

Installation and commissioning of the modems and routers

5.9 Installing and putting a SINAUT MD2, MD3, MD4 modem into operation

SINAUT ST7 station control system
System Manual, 09/2016, C79000-G8976-C178-10

233

Permitted ambient temperature
The SINAUT modems can be operated in the same temperature range specified for the S7-

300.

Table 5- 50 Permitted ambient temperature for SINAUT modems

Installation position

Permitted ambient temperature

Horizontal

0 to 60 °C

Vertical

0 to 40 °C

Dimensions for installing SINAUT modems

Table 5- 51 Dimensions for installing SINAUT modems

Module

Module width

Module height

Max. depth

Modem module

MD2, MD3 and MD4

80 mm

125 mm

120 mm or 180 mm

with open front panel

5.9.5

Connecting to the power supply

WARNING

Danger with the power turned on
Connecting the modem module when the power is on can damage the module. Therefore

connect the modem to the power supply only when the power supply is off.

Содержание SIMATIC NET TeleControl SINAUT ST7







































































































































































































































































































Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Бренды по названию

Популярные бренды

Siemens SIMATIC NET TeleControl SINAUT ST7, Системное руководство

Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Бренды по названию

Популярные бренды