manualshive.com logo in svg

Siemens SIMATIC NET TeleControl SINAUT ST7, Системное руководство

Поделиться
Скачать
Siemens SIMATIC NET TeleControl SINAUT ST7 Скачать руководство пользователя страница 223

 

Installation and commissioning of the modems and routers 

 

5.8 ISDN dial-up modem MD4 

SINAUT ST7 station control system 
System Manual, 09/2016, C79000-G8976-C178-10 

223

 

5.8.2

 

Configuration switches accessible from above 

Configuration switches accessible from above 

The following figure shows the MD4 modem from above. It shows the location of the 4-pin 

DIL switch that is accessible from above. 

 

Figure 5-48  View of the MD4 modem from above 

Settings with the DIL switches accessible from above 
The MD4 modem has a 4-pin DIL switch mounted directly on the grill of the housing. 
The DIL switch has the following function: 

●

 

Setting the mode 

●

 

Setting one of the four standard profiles for the dialing mode 

●

 

Reset function 

The following figure summarizes the possible settings. 

Содержание SIMATIC NET TeleControl SINAUT ST7







































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды