Siemens SIMATIC NET TeleControl SINAUT ST7 Скачать руководство пользователя страница 152

Страница: 152 / 294

Installation and commissioning of the modems and routers

5.4 GPRS/GSM router MD741-1

SINAUT ST7 station control system

152

System Manual, 09/2016, C79000-G8976-C178-10

Installation on a 35 mm standard rail

The SINAUT MD741-1 is intended for installation on DIN rails complying with DIN EN 50022.

There is a suitable fastener on the rear of the device.

Table 5- 8

Dimensions of the MD741-1 router

MD741-1

Dimensions

W x H x D (mm)

45 x 99 x 114

Depth with connected antenna / Ethernet cable (mm)

approx. 170

5.4.2

Connecting the MD741-1 to the TIM and antenna

The following figure shows how the GPRS router MD741-1 is connected to a TIM over its

Ethernet connector (IE) and how the SMA connector is connected to an antenna.

Figure 5-4

Connecting the MD741-1 to a TIM and an antenna

5.4.3

Prerequisites for operation

To use the MD741-1, the following requirements must be met:

●

A subscriber contract with GSM network operator that supports GPRS

●

SIM card for enabling GPRS for the user by the network operator

Содержание SIMATIC NET TeleControl SINAUT ST7







































































































































































































































































































Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Похожие инструкции для SIMATIC NET TeleControl SINAUT ST7

Бренды по названию

Популярные бренды

Siemens SIMATIC NET TeleControl SINAUT ST7, Системное руководство

Результаты поиска

Содержание SIMATIC NET TeleControl SINAUT ST7

Отзывы:

Похожие инструкции для SIMATIC NET TeleControl SINAUT ST7

Бренды по названию

Популярные бренды