Raytheon Anschütz NautoPilot 5000 Series Скачать руководство пользователя страница 9

Страница: 9 / 191

NautoPilot® 5000 Series

102-890.NG001-NG003

Operator Manual

Edition: 003

VII

10000001052

Table of Figures

Figure 1: NautoPilot® 5000 Series, Operator Unit .................................................................................... 2

Figure 2: Additional Autopilot Control Unit (AACU) ................................................................................... 4

Figure 3: Standalone application for the NautoPilot® 5000 Series ........................................................... 5

Figure 4: Integrated application of NautoPilot® 5000 Series .................................................................... 5

Figure 5: Course Trim angle .................................................................................................................. 12

Figure 6: Heading Control after manual set heading adjustment ............................................................ 18

Figure 7: Principle of Course Control versus Heading Control ................................................................ 19

Figure 8: Explanations for a heading change in Course Control ............................................................. 20

Figure 9: Principle of Course Control display ......................................................................................... 20

Figure 10: Course Control after manual set heading adjustment ............................................................ 21

Figure 11: Principle of Track Control ...................................................................................................... 23

Figure 12: Example for GO- TO- WAYPOINT Maneuver for NP5100, NP5300 and NP5400 ................. 27

Figure 13: Geometrical Requirements of GO- TO- WAYPOINT maneuvers ........................................... 28

Figure 14: Example of Five Different GO- TO- WAYPOINT maneuvers depending on the initial heading
.............................................................................................................................................................. 28

Figure 15: Changing over to Track Control - on transmitting a FROM- WPT by the ECDIS .................... 32

Figure 16: Procedure of the Track Change maneuver (Example) ........................................................... 33

Figure 17: Extreme Case Example of a Track Change maneuver .......................................................... 35

Figure 18: Changing TO- WPT and NEXT- WPT without Interrupting Track Control .............................. 36

Figure 19: Intended RETURN- TO- TRACK maneuver Impossible with the Ship too Close to the TO-
WPT....................................................................................................................................................... 43

Figure 20: Track Control impossible with the Distance to the Track too large ......................................... 43

Figure 21: NautoPilot® Operator Unit (operation elements) ................................................................... 47

Figure 22: Structure to adjust parameters and values ............................................................................ 50

Figure 23: First display (after switching ON the NautoPilot® Operator Unit) ........................................... 51

Figure 24: Tendency bar ........................................................................................................................ 54

Figure 25: First display (after switching ON the NautoPilot® Operator Unit in night mode, black/white) . 55

Figure 26: First Display (heading changes with RoT is selected). .......................................................... 56

Figure 27: First Display (Eco/Prec switchover) ....................................................................................... 57

Figure 28: Switching to display selection ................................................................................................ 58

Figure 29: Displays for HDG /Rudder Plot .............................................................................................. 59

Figure 30: Example of a SET request after a parameter has been changed .......................................... 59

Figure 31: Displays for Track Data ......................................................................................................... 62

Figure 32: Example of a request to press SET after a parameter has been changed ............................. 63

Figure 33: Display for NP 5000 Actual Rudder with one and 2 rudders .................................................. 65

Содержание NautoPilot 5000 Series
































































































































































































Результаты поиска

Содержание NautoPilot 5000 Series

Отзывы:

Похожие инструкции для NautoPilot 5000 Series

Бренды по названию

Популярные бренды

Raytheon Anschütz NautoPilot 5000 Series, Руководство оператора

Результаты поиска

Содержание NautoPilot 5000 Series

Отзывы:

Похожие инструкции для NautoPilot 5000 Series

Бренды по названию

Популярные бренды