Raytheon Anschütz NautoPilot 5000 Series Скачать руководство пользователя страница 190

Страница: 190 / 191

NautoPilot Operator Unit

8 Annex

10000001052

Edition:001

Alert Title
Alert Description

Catego-

ry
Priority

Escala-

tion

Possible Cause

Remedy

CHECK DR
CHECK DEAD

RECKONING DRIFT

SETTINGS

Caution
B

none

Position monitor for

Course control uses

DR. Default settings

used for drift and set.

Check settings for po-

sition monitor

CRS APPROACH
COURSE AP-

PROACHING

Caution
B

none

Activation of Course

control or Set course

change in course

control.

NO BACKUP POS
NO BACKUP

POSITION USING

DEAD RECKONING

Caution
B

none

Dead reckoning is

used for position

monitoring.

None necessary.

POS MON SOG
DEAD RECKONING

WITH SOG: CHECK

SPEED SENSOR

Caution
B

Position monitor uses

a dead reckoning po-

sition for comparison.

Tab. 15: Alerts Track Control Old

Alert Title
Alert Description

Catego-

ry
Priority

Escala-

tion

Possible Cause

Remedy

CHANGE TRACK
CHANGING TRACK

TO 000°

Alarm
A

to BN-

WAS

Only active if AP

is configured for

IEC62065:2002. Ac-

tual Course change

warning (30 s prior to

WOL)

CHANGE TRACK
CHANGING TRACK

TO 000°

Alarm
A

Alarm
to BN-

WAS

Only active if AP

is configured for

IEC62065:2002. Ac-

tual Course change

warning (WOL al-

ready passed)

NEW CRS 30S
COURSE CHANGE

IN 30 SECONDS

Warning
A
(30 s)*

Track 62065:2002,

actual track change

warning.

Содержание NautoPilot 5000 Series
































































































































































































Результаты поиска

Содержание NautoPilot 5000 Series

Отзывы:

Похожие инструкции для NautoPilot 5000 Series

Бренды по названию

Популярные бренды

Raytheon Anschütz NautoPilot 5000 Series, Руководство оператора

Результаты поиска

Содержание NautoPilot 5000 Series

Отзывы:

Похожие инструкции для NautoPilot 5000 Series

Бренды по названию

Популярные бренды