Raytheon Anschütz NautoPilot 5000 Series Скачать руководство пользователя страница 188

Страница: 188 / 191

NautoPilot Operator Unit

8 Annex

10000001052

Edition:001

Alert Title
Alert Description

Catego-

ry
Priority

Escala-

tion

Possible Cause

Remedy

WP CHANGED
WAYPOINTS HAVE

CHANGED

Caution
A

none

The current TO-Way-

point was changed

while in track control

XTE EXCEEDED
OFF TRACK CROSS

TRACK LIMIT EX-

CEEDED

Alarm
A

Ship is outside of ad-

justed limits around

the current leg.

Check surroundings,

use manual steering

XTE MISSING
CHECK CONNEC-

TION TO ECDIS

Caution
B

none

XTE TO LARGE
XTE GREATER

THAN 000NM

Caution
B

none

Activation of track

control from ECDIS,

XTE is greater than 1

nautical mile

Tab. 14: Alerts Course Control

Alert Title
Alert Description

Catego-

ry
Priority

Escala-

tion

Possible Cause

Remedy

CC STOPPED
NO HEADING:

USE MANUAL

STEERING

Alarm
B

to BN-

WAS

Course control

stopped, Heading in-

formation missing

Check heading infor-

mation, use manual

steering

CC STOPPED
NO SPEED: CHECK

SPEED SENSOR

Alarm
B

to BN-

WAS

Course control

stopped, Speed infor-

mation missing

Use manual steering

or HDG control

CC STOPPED
NO POSITION:

CHECK POSITION

SENSORS

Warning
B

Alarm
to BN-

WAS

Course control was

stopped since no po-

sition data is avail-

able.
Heading control is ac-

tive, actual heading is

used as set heading.

Check position sen-

sors. Use Heading

control or manual

steering.

CC STOPPED
MAG HEAD-

ING SELECTED:

SELECT GYRO

HEADING

Warning
B

Alarm
to BN-

WAS

Course control was

stopped since a mag-

netic heading sensor

was selected.

Select a Gyro head-

ing sensor.

Содержание NautoPilot 5000 Series
































































































































































































Результаты поиска

Содержание NautoPilot 5000 Series

Отзывы:

Похожие инструкции для NautoPilot 5000 Series

Бренды по названию

Популярные бренды

Raytheon Anschütz NautoPilot 5000 Series, Руководство оператора

Результаты поиска

Содержание NautoPilot 5000 Series

Отзывы:

Похожие инструкции для NautoPilot 5000 Series

Бренды по названию

Популярные бренды